background image

NIBCO, Inc.

 

6

 

1516 Middlebury Street • Elkhart, IN 46516 USA • 888-446-4226

PC-10M Battery-powered Pressing Tool

Operation

Electric shock hazard:
This tool is not insulated. When 

using this unit on or near energized 

electrical lines, use proper personal 

protective equipment.
Failure to observe this warning could 

result in severe injury or death.

Wear eye protection when operating 

or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from 

flying debris or hydraulic oil. 

Inspect tool before use. Replace any worn or 

 damaged parts. A damaged or improperly  

assembled tool can break and strike bystanders. 
Failure to observe this warning could result in severe 

injury or death.

•  Do not use this tool for continuous use. After  

30 to 40 cycles, allow the tool to cool for 15 

minutes.

•  Do not secure this tool in a vise. This tool is 

designed for hand-held operation.

•  This tool may be used in damp or wet environ-

ments; however, air-drying is recommended before 

use if the tool becomes soaked. Damage may 

result when the tool is operated prior to thorough 

drying when electrical components are soaked.

•  Use this tool for the manufacturer’s intended 

purpose only.

Failure to observe these precautions may result in 

injury or property damage.

Charging the Battery

Read the instructions supplied with the battery charger.

Important Features of the Unit

•  The hydraulic unit incorporates an automatic retraction 

which returns the drive rollers into its starting position 

when the maximum operating pressure is reached.

•  The unit is equipped with a special brake which stops 

the forward motion of the drive rollers when the trigger 

is released.

•  The pressing head can be smoothly turned by 350° 

around the longitudinal axis in order to gain better 

access to tight corners and other difficult working areas.

An incomplete press can cause leaks.
•  Use proper fitting and copper tubing combina-

tions. Improper combinations can result in an 

incomplete press.

•  The relief valve will sound and the drive rollers 

automatically retracts when a complete press 

has been achieved. If you do not hear a “pop” 

and the drive rollers do not automatically retract, 

the press is not complete.

Failure to observe these precautions may result in 

injury or property damage.

Pinch points:
Keep hands away from the pressing 

tool head when pressing.
Failure to observe this warning could 

result in severe injury or death.

Содержание PC-100M











Отзывы: