NI SCC-RLY01 Скачать руководство пользователя страница 1

USER GUIDE

SCC-RLY01 Relay Module

The SCC-RLY01 contains one single-pole double-throw (SPDT) 
nonlatching relay capable of switching 5 A at 30 VDC when using an 
SC-2345 or SC-2350, or 250 VAC when using an SCC-68. Any single 
E/M Series DAQ device digital input/output (P0) line 0 to 7 can control the 
SCC-RLY01.

The SCC-RLY01 uses positive logic. A digital high sets the relay, and 
a digital low resets it. In the set state, the common (COM) contact is 
connected to the normally open (NO) contact. In the reset state, the 
common (COM) contact is connected to the normally closed (NC) contact.

Conventions

The following conventions are used in this guide:

<>

Angle brackets that contain numbers separated by an ellipsis represent 
a range of values associated with a bit or signal name—for example, 
P0 <3..0>.

»

The 

»

 symbol leads you through nested menu items and dialog box options 

to a final action. The sequence 

File»Page Setup»Options

 directs you to 

pull down the 

File

 menu, select the 

Page Setup

 item, and select 

Options

 

from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to 
avoid injury, data loss, or a system crash.

 

When this symbol is marked on 

the product, refer to the 

Read Me First: Safety and Radio-Frequency 

Interference

 document, shipped with the product, for precautions to take.

When symbol is marked on a product, it denotes a warning advising you to 
take precautions to avoid electrical shock.

When symbol is marked on a product, it denotes a component that may be 
hot. Touching this component may result in bodily injury.

Содержание SCC-RLY01










Отзывы: