NI PXI-8108 Скачать руководство пользователя | Manualshive

Страница: 34 / 86

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-19

NI PXI-8108 User Manual

8.

Install the LabVIEW Real-Time software and device drivers that you
require on the RT target. Refer to the NI Web site at

ni.com/info

and

enter the info code

etspc

for the latest information about supported

software.

After installation of the software the controller will automatically reboot
and you will now be able to program it using LabVIEW Real-Time.

Note

Refer to the

RT Getting Started Guide

available on your host computer for more

information about setting up your RT target.

LabVIEW RT Configuration Switches

Use the LabVIEW RT configuration switches to configure LabVIEW RT
if it is installed on the controller. If you are not using LabVIEW RT, these
switches should remain in the OFF position. The controller reads these
switches only after a system reset.

Note

You must reboot the controller for any changes to take place.

The NI PXI-8108 controller includes the following LabVIEW RT
configuration switches:

•

Switch 1—

Boot LabVIEW RT

: Set this switch to ON to boot

LabVIEW RT.

•

Switch 2—

Boot Safe Mode

: Set this switch to ON to boot LabVIEW

RT into safe mode to reconfigure TCP/IP settings and to download or
update software from a host computer. This switch overrides the
behavior of Switch 1. Booting the controller into safe mode does not
start the embedded LabVIEW RT engine. After changing the settings
or software, reboot the controller with this switch OFF to resume
normal operation.

•

Switch 3—

Disable Startup VI

: Set this switch to ON to prevent VIs

from automatically running at startup if the controller becomes
inaccessible because of a startup VI.

•

Switch 4—

Reset IP Address

: Set this switch to ON to reset the

IP address and other TCP/IP settings to their factory defaults. Use this
switch if moving the controller to a different subnet or if the current
TCP/IP settings are valid.

Note

By default, the target will automatically attempt to connect to the network using

DHCP. If the target is unable to initiate a DHCP connection, the target connects to the
network with a link-local IP address or

169.254.x.x

.

«
...
32
33
34
35
36
...
»

Содержание PXI-8108























































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8108

Бренд: PACH & COMPANY Страницы: 4

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: Centurion Страницы: 16

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Бренд: LCT Страницы: 5

Бренд: Bardiani Valvole Страницы: 118

Бренд: Lab-T Страницы: 17

Бренд: B meters Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: Seneca Страницы: 8

Бренд: MAKOT Страницы: 6

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

Бренд: Autotrol Страницы: 8

DECORA ILLUMATECH IPF01-1LX

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды