Before setting up the detector, please firstly get the adapter wire through
the bottom cable management holes. (There are four cable management
holes, please find one proper position.) Connect the power socket in
mentioned position, and power on AC adapter.
7. Installation - Preparation Procedure
1. Open the mounting bracket, and get the adapter wire go through the mentioned
hole.
2. Please write down installing date on the detector in the position where agent
has suggested.
3. After power on, please hear Beep sound to ensure the proper detector setup.
4. Please make sure the linking status for the wireless type. Green LED flashes
every 2 seconds in normal status.
Installed
on
yy / mm
8. Installation – Mounting Procedure
……………
…
……………
…
1
2
3
1
66.8㎝
……………
………
……………
2
3
4
2
66.8㎝
Please fix the detector with two screws on ceiling or wall.
1. Fix the mounting bracket with two screws.
2. Place the detector in the rail of mounting bracket.
3. Turn the detector clockwise until hear a sound “KA” meaning fixing
tightly.
………
1
1
Please fix the detector with two screws on ceiling or wall.
1. Drill 2 holes on expected mounting position for 5mm for diameter
and 25 mm in depth.
2. Fix the mounting bracket with two screws.
3. Place the detector in the rail of mounting bracket.
4. Turn the detector clockwise until hear a sound “KA” meaning fixing
tightly.
Mounting on ceiling or wall
Mounting on concrete wall
Warning
(1) Please mark the expected installing position on wall in advance
that is helpful for drilling holes
(2) Please make the Test / Mute button face down for best operation.
Method for verifying detector(s) operation normally :
Please verify detector function properly after installation and inspection.
Please press Test Button for 1 second for operation verification. Within 1 ~ 5
seconds, you will hear
“
Operations : Normal
＂
meaning the detector functions
normally; on the contrast you will hear Beep Beep meaning the detector function
abnormally and it needs to proceed further treatment(s). Please refer to below
Status and notification table indications :
When you hear “Danger! Evacuate!” from the detector(s) and see the red LED
flashing, please follow below SOP or local emergency SOP and act immediately :
Please confirm the exact location of CO leakage and call the Fire department
after evacuate oneself. Except for CO leakage, siren could be activated in following
conditions. User can stop the alarming siren by ventilating the environment around
the detector(s).
•
When the pesticide sprinkles on the detector directly.
•
When the sanitizer sprinkles on detector.
•
When the gas detector has condensed.
•
When bugs or incents enter the detector chamber.
9. Operation Verification
Please verify operation normally when using Wireless Type CO Detector
11. When your hear the siren from the detector(s)
---
---
Indication
---
---
---
---
---
---
Green & Red LED
lights ON for 1 sec
Status
Action
Voice and
Sound
Wireless Link LED
Green LED flashes
once per 5 seconds
Green LED flashes
once per 2 seconds
Green LED flashes
twice per 5 seconds
Green LED flashes
3 times
Red LED flashes
continuously
Please press S1
on gateway
Please follow
Troubleshooting
Press 3 times
on S1
Press S1 for
5 seconds
Not connected to
gateway
Connected to
gateway successfully
Normally connected
Disconnection
Leave network
Reset
---
Indication
Status
Action
Power On
Normal Detecting
Alarming
“Beep”
---
“Danger! Evacuate! ”
Plug in AC adapter
Follow local
emergency SOP
Flashes for
30 seconds
Flashes once
per minute
Flashes
continuously
Voice and Sound
Alert LED (Red)
•
Please check the operation of detector every 6 months.
•
Please check if there is dust or stink attached on the CO detector chamber.
This will potentially cause false-alarm.
•
Please withdraw the detector from mounting bracket. And clean the ceiling
or wall around the detector.
•
Please clean the whereabouts of the detector after detaching the detector.
•
Please do NOT let the water of wet cloth leaks into the detector.
•
Please do NOT use the volatile cleaner to clean the detector, it may cause
the damage on the surface of the detector.
•
Disposed detector should strictly follow laws of local waste management.
12 Periodic Maintenance and Inspection
13 Troubleshooting
Status
Inspection
Treatment
Press Test button
and keep
“Beep, Beep”
meaning
function error
Is the test button has been
pressed accidentally?
Please power on the
device again.
Wireless
disconnection
Is there is block between
detector and receiver?
Please add router in
between
Is there any powerful radio
radiation that Interrupts the
current wireless signal?
Please remove the radio
radiation source, or add
router in between.
Please remove the block
in between
AC adapter
adapter wire
cable management hole
cable management hole
Flashes twice
Installing the po
wer supply
power
socket
Flashes 4 times
“Operations: Normal”
---
“Beep, Beep” per
minute
Abnormal
Operation
Normal Operation
Follow
troubleshooting
(For SG-02-CO-H1 wireless model only; will require a parent device
[coordinator/gateway, e.g. G07])
1. Please join your detector to the parent device’s wireless IoT (Internet of Things) network.
2. Please go to Sentrol Cloud website ( http://www.sentrolcloud.com ) or download
and launch Sentrol Cloud APP, then follow instructions to register and activate
a Sentrol Cloud account.
3. Login to Sentrol Cloud platform via Sentrol Cloud website or Sentrol Cloud APP.
4. Your parent device will receive statuses from your detector (alarm/non-alarm),
and the cloud platform/APP will notify you of any alarms. For more detailed
remote monitoring instructions, please refer to instructions on Sentrol Cloud
website.
10 Remote Monitoring of Wireless CO Detector