Nexans Euromold 200LR Скачать руководство пользователя страница 7

Страница: 7 / 9

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

CONNECTOR INSTALLATION ON THE BUSHING

Clean and lubricate* lightly both

bushing interface and elbow connector

interface.

Place the elbow connector firmly down

on the bushing

Insert bail into the bushing tabs and

position bail over elbow connector

NOTE :

A connector/bushing mated combination should not be allowed to carry the full weight of the cable.

Therefore it is necessary to clamp the cable as close as possible to the connector.

IMPORTANT NOTES :

- Never disconnect the connector from energised equipment nor energise a disconnected connector

without previously installing an appropriate mating part.

- Do not allow hydrocarbon oils or solvents to contaminate the E.P.D.M. rubber.

In the event of contamination, wipe the surface clean with a dry cloth.

Connect earthing lead of the connector and flexible braid to the system earth.

lubricate

equipment

bushing

Installation hint :

Apply a small dash of silicone grease on the

connector’s surface to easily snap the bail

into position.

silicone

grease

Page 7/9

IS97082-ENG - 200LR/G

-MT345 - Revision 0

Содержание Euromold 200LR










Результаты поиска

Содержание Euromold 200LR

Отзывы:

Бренды по названию

Популярные бренды

Nexans Euromold 200LR, Руководство по установке

Результаты поиска

Содержание Euromold 200LR

Отзывы:

Бренды по названию

Популярные бренды