Newton S страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 40

background image

NEWTON S

23

SYSTEM OPERATION MANUAL

2. Move the selector to the

DO PAIRING

option using the

DOWN

and

UP

buttons and press

SELECT

. The message “RADIO PAIRING IN PROGRESS” will be displayed

3. Turn on the remote head

4. The pairing procedure can take up to 60 seconds. When the pairing is completed the message

“RADIO PAIRING SUCCESSFUL” will be displayed. To abort the procedure, press

CANCEL

Figure 5.4: Newton C1 Settings - Radio tab

5.4.2

ETHERNET

Under the

ETHERNET

settings tab the Ethernet connection is configured, such as the IP address

and net-mask of the Newton C1 as well as the IP address of the remote head. The Newton C1 and the
remote head must be on the same IP subnet. Note that the Newton C1 and Newton S are configured
to be compatible with each other as default.

If the setting

AUTOCONNECT

is set to ENABLE the Newton C1 will try to connect as soon as a

valid physical link is established. It will also automatically reconnect should the connection break for
any reason. When

AUTOCONNECT

is set to DISABLED, the Ethernet connection must be manually

initiated by selecting

CONNECT

.

WARNING

If

AUTOCONNECT

is set to ENABLE in a use-case where radio is the

prefered transport and an ethernet connection is not expected to be

available, it can lead to stutter in control and loss of connection.

If using radio, set

AUTOCONNECT

to DISABLED.

DO NOT DISTRIBUTE

Copyright © 2019 Newton Nordic AB

«
...
25
26
27
28
29
...
»

Содержание S









































Отзывы:

Нет отзывов

Похожие инструкции для S

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 2

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 2

Бренд: GE Страницы: 85

Бренд: GE Страницы: 85

Бренд: GE Страницы: 85

Schneider D-XENOGON 35

Бренд: Samsung Страницы: 24

20-50mm F3.5-5.6 ED II

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды