Newland EM3080-W-V2 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 29

background image

23

Dimensions of the Connector

The EM3080-W V2 uses a 12-pin FPC connector.

12-pin FPC Connector

The EM3080-W V2 uses a 12-pin ZIF connector (bottom contact). This connector can be connected to a host device with

an FFC cable. Parameters are shown as below.

Figure 4-2

FFC Cable (unit: mm)

A 12-pin FFC cable (contacts on the same side or on opposite sides) can be used to connect the EM3080-W V2 to a host

device. The cable design must be consistent with the specifications shown below. Use reinforcement material for the

connectors on the cable and reduce cable impedance for reliable connection and stable performance.

Figure 4-3

«
...
21
22
23
24
25
...
»

Содержание EM3080-W-V2






























Отзывы:

Нет отзывов

Похожие инструкции для EM3080-W-V2

Бренд: Uniden Страницы: 40

Бренд: EMSCAN Страницы: 86

90-8010-200 - DocuMate 250

Бренд: Xerox Страницы: 88

Бренд: Uniden Страницы: 10

Colortrac imagePROGRAF MFP Z36

Бренд: Canon Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: Panasonic Страницы: 2

Бренд: ABB Страницы: 190

Бренд: Canon Страницы: 2

Бренд: Lamtec Страницы: 24

Бренд: AGFA Страницы: 28

Бренд: AGFA Страницы: 36

Бренд: AGFA Страницы: 46

Бренд: AGFA Страницы: 54

Бренд: Rollei Страницы: 25

Бренд: Microtek Страницы: 2

ArtixScan 1800f

Бренд: Microtek Страницы: 30

ArtixScanDI 2015c

Бренд: Microtek Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды