Newland EM3080-W-V2 Скачать руководство пользователя страница 28

Страница: 28 / 29

Chapter 5 Configuration Tools

There are two configuration tools which support application development for the EM3080-W V2. They can meet the needs

of rapid assessment and development and functional configuration.

EVK

The supplied EVK tool can assist users in application development for the EM3080-W V2. EVK contains Beeper, Beeper

driver circuit, LED, LED driver circuit, Trigger key, Reset key, RS-232 interface and USB interface. You can connect the

EVK with the EM3080-W V2 via the 12-PIN FFC cable and connect the EVK to PC via a USB connection or an RS-232

connection.

EasySet

EasySet, developed by Fujian Newland Auto-ID Tech. Co., Ltd., is a Windows-based configuration tool. Connect the

Easyset with the EM3080-W V2, enabling users to gain access to decoded data and captured images and to configure the

engine.

Содержание EM3080-W-V2






























Результаты поиска

Содержание EM3080-W-V2

Отзывы:

Похожие инструкции для EM3080-W-V2

Бренды по названию

Популярные бренды

Newland EM3080-W-V2, Руководство по интеграции

Результаты поиска

Содержание EM3080-W-V2

Отзывы:

Похожие инструкции для EM3080-W-V2

Бренды по названию

Популярные бренды