New Yorker CL3-105 Скачать руководство пользователя страница 34

Страница: 34 / 64

Figure 27: Cad Cell Location

V: SYSTEM START-UP (continued)

CHECK FOR CLEAN CUT OFF OF

BURNER.

1. AIR IN THE OIL LINE between fuel unit and

nozzle will compress when burner is on and will

expand when burner stops, causing oil to squirt from

nozzle at low pressure as burner slows down and

causing nozzle to drip after burner stops. Usually

cycling the burner operation about 5 to 10 times will

rid oil line of this air.

2. IF NOZZLE CONTINUES TO DRIP, repeat

Paragraph H, Step 1 above. If this does not stop the

dripping, remove cut-off valve and seat, and wipe

both with a clean cloth until clean, then replace

and readjust oil pressure. If dripping or after burn

persist replace fuel pump.

TEST CONTROLS.

1. Check thermostat operation. Raise and lower

thermostat setting as required to start and stop

burner.

WARNING

Before installation of the boiler is considered

complete, the operation of all boiler controls must

be checked, particularly the primary control and

high limit control.

VERIFY OIL PRIMARY CONTROL

FEATURES

using procedures outlined in

Instructions furnished with control or instructions as

follows:
a.

GeniSys 7505 Control Features

, see Figure 28

The GeniSys 7505 is a microprocessor-

based control. The indicator light provides

diagnostic information for lockout, recycling

and cad cell status. There is a manual reset

button to exit the Lockout Mode.

ii.

Pump Priming Cycle: To facilitate purging

air from the oil lines and filters, the 7505 can

be placed in a purge routine by:

• After the burner starts, press and hold the

reset button for 15 seconds until the

yellow light turns on. This indicates that

the button has been held long enough.

• Release the reset button. The yellow

light will turn off and the burner will start

up again.

• At burner start up, click the reset button

while the igniter is till on. This will

transition the control to a dedicated

Pump Prime mode, during which the

motor, igniter, and valve are powered for

four (4) minutes. The yellow light will be

on.

• At the end of four (4) minutes, the yellow

light will turn off and the control will

automatically return to standby mode.

iii.

Limited Recycle:

This feature limits the

number of recycle trials (for each call

for heat) to a maximum of three trials. If

the flame is lost three times and does not

successfully satisfy a call for heat, the 7505

locks out.

iv.

Limited Reset (Restricted Mode):

In order

to limit the accumulation of unburned oil in

the combustion area, the control can only be

reset three times. The reset count returns to

Figure 28: GeniSys 7505 Oil Primary Terminals,

LED's and Reset Button

Содержание CL3-105

































































Результаты поиска

Содержание CL3-105

Отзывы:

Похожие инструкции для CL3-105

Бренды по названию

Популярные бренды

New Yorker CL3-105, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CL3-105

Отзывы:

Похожие инструкции для CL3-105

Бренды по названию

Популярные бренды