New Yorker CL3-105 Скачать руководство пользователя страница 21

Страница: 21 / 64

a. CL SERIES WATER BOILER - Figures 11A

and 11B show indirect water heater piping on

typical hot water heating system. Boiler piping

is the same as for any two-zone system. Figures

11A and 11B show circulator zoning, which is

usually preferred for indirect water heaters. Size

the circulator and indirect water heater piping to

obtain the boiler water flow through the indirect

water heater called for by the indirect water

heater manufacturer. Refer to the indirect water

heater instruction manual for additional details.

b. CL SERIES STEAM BOILER - All CL Series

steam boilers are equipped with tappings to

permit the connect of an indirect water heater,

see Figures 2B and 15. In this type of system,

hot boiler water is drawn from below the water

line and passed through the heat exchanger in the

indirect water heater.

This section describes boiler-side piping only.

Refer to the indirect water heater instruction

manual for additional details.

INSTALL SMOKEPIPE — The CL Series boiler

should be vented into a fireclay tile-lined masonry

chimney or chimney constructed from type L vent or

a factory built chimney that complies with the type

HT requirements of UL103. The chimney and vent

pipe shall have a sufficient draft at all times, to assure

safe proper operation of the boiler. See Figure 16 for

recommended installation.
1. Install a draft regulator (supplied by installer)

following the instructions furnished with the

regulator. See Figure 17 for draft regulator locations.

2. Consider the chimney overall. Chimneys that have

a high heat loss may become less suitable as the

heat loss of the home goes down and the efficiency

of the boiler installed goes up. Most homes have

a chimney appropriate for the fuel and the era in

which the home was built. That may have been a

coal fired or an inefficient oil fired boiler built into

a home without insulation or storm windows. With

increasing fuel prices that home probably has been

insulated and fitted with storm windows so that

the heat loss of the home has been reduced. This

requires less fuel to be burned and sends less heat up

the chimney.

A new boiler probably has a higher efficiency than

the boiler being replaced. That probably means that

the stack temperature from the new boiler will be

lower than that from the old boiler and with less

room air being drawn up the chimney to dilute the

stack gases. The combination of a large uninsulated

chimney, reduced firing rate, reduced firing time,

III: INSTALLATION INSTRUCTIONS (continued)

Figure 16: Recommended Smokepipe Arrangement and

Chimney Requirements

Figure 15: Indirect Water Heater Piping on CL Series Steam Boiler

Содержание CL3-105

































































Результаты поиска

Содержание CL3-105

Отзывы:

Похожие инструкции для CL3-105

Бренды по названию

Популярные бренды

New Yorker CL3-105, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CL3-105

Отзывы:

Похожие инструкции для CL3-105

Бренды по названию

Популярные бренды