background image

SECTION 1 - GENERAL INFORMATION

1-3

SPECIFICATIONS

MZ19H

ENGINE

Type...............................................................

Kawasaki

Model.............................................................

FH580V

Horsepower ...................................................

14.2 kw (19)@3600 RPM

Cylinders........................................................

V-Twin

Displacement.................................................

585CC (35.7 cu. in.)

Low Idle Speed..............................................

1400 RPM

Maximum Speed:
    High Idle ....................................................   3400 RPM
Oil Capacity ...................................................

1.9 qt. (1.8L)

Spec Number.................................................

AS13

Fuel Unleaded Gasoline ................................

87 octane min.

Vertical Shaft .................................................

1 in. (2.54 cm) Dia

Charge coil ....................................................

12v - 13 amp

Other..............................................................

Air  cooled, Dual element air cleaner, Fuel pump,
Overhead valve, Four cycle, Electronic ignition, Full
pressure lubricated with oil filter

CONSTRUCTION

Front Frame...................................................

Welded 1 x 2 x .120 structural steel tube

Rear Frame ...................................................

Welded, 7 and 10 ga. high strength steel

Frame Assembly............................................

Front and rear frames bolted together

FUEL SYSTEM 

Capacity.........................................................

5 Gallon (18.9 L)

Type...............................................................

Single fuel tank fender mounting on left side

Other..............................................................

Fuel tank shut-off, Fuel filter (replaceable in-line type),
Large diameter vented fuel cap, Tank includes molded
beverage holder

TRACTION SYSTEM

Transaxles .....................................................

Twin Hydro-Gear Hydrostatic Transaxles

Transaxle Drive .............................................

Belt drive with self-tensioning system

Ground speed................................................

Infinite, 0 to 7-MPH (10.5-km/hr) forward, 0 to 3.4-MPH
(5.5-km/hr) reverse

Transport Rods..............................................

Allow unit to be moved without engine running

ATTACHMENT DRIVE

Clutch ............................................................

Electric Clutch

Type...............................................................

Vertical drive with single deep B-groove Pulley

Find manuals at https://best-manuals.com

Содержание MZ19H






















Отзывы: