Do not operate this machine unless you have
read and understand the instructions in the
OPERATOR’S MANUAL. Improper machine
operation is dangerous and could result in injury
or death.
6.
Relieve all pressure in air, oil or water systems
before any lines, fittings or related items are
disconnected or removed. Always make sure
all raised components are blocked correctly
and be alert for possible pressure when
disconnecting any device from a system that
utilizes pressure.
7.
Lower the bucket, blade or other attachments
to the ground before performing any work on
the machine. If this cannot be done, make sure
the bucket, blade or other attachment is
blocked correctly to prevent it from dropping
unexpectedly.
8.
Use steps and grab handles when mounting or
dismounting a machine. Clean any mud,
grease, oil or debris from steps, walkways or
work platforms before using. Always face the
machine when using steps, ladders and
walkways. When it is not possible to use the
designed access system, provide ladders,
scaffolds, or work platforms to perform safe
repair operations.
9.
To avoid back injury, use a hoist when lifting
components which weigh 23 kg (50 lbs) or
more. Make sure all chains, hooks, slings, etc.,
are in good condition and are the correct
capacity. Be sure hooks are positioned
correctly. Lifting eyes are not to be side loaded
during a lifting operation.
10. To avoid burns, be alert for hot parts on
machines which have just been stopped and
hot fluids in lines, tubes and components.
11. Be careful when removing cover plates.
Gradually back off the last two bolts or nuts
located at opposite ends of the cover or device
and carefully pry cover loose to relieve any
spring or other pressure, before removing the
last two bolts or nuts completely.
12. Be careful when removing filler caps,
breathers and plugs on the machine. Hold a
rag over the cap or plug to prevent being
sprayed or splashed by liquids under pressure.
The danger is even greater if the machine has
just been stopped because fluids can be hot.
13. Always use the proper tools that are in good
condition and that are suited for the job at
hand. Be sure you understand how to use
them before performing any service work.
14. Reinstall all fasteners with the same part
number. Do not use a lesser quality fastener if
replacements are necessary.
SAFETY PRECAUTIONS
1.2
SAFETY PRECAUTIONS
The serviceman or mechanic may be unfamiliar
with many of the systems on this machine. This
makes it important to use caution when
performing service work. A knowledge of the
system and or components is important before
the removal or disassembly of any component.
Because of the size of some of the machine
components, the serviceman or mechanic
should check the weights noted in this manual.
Use proper lifting procedures when removing
any components. Weight of components table
for SK40SR-2 / SK45SR-2 is shown in page
02-1-7, 8 of chapter SPECIFICATIONS in this
manual.
The following is a list of basic precautions that must
always be observed.
1.
Read and understand all warning plates and
decals on the machine before operating,
maintaining or repairing this machine.
2.
Always wear protective glasses and protective
shoes when working around machines. In
particular, wear protective glasses when using
hammers, punches or drifts on any part of the
machine or attachments. Use welders gloves,
hood/goggles, apron and the protective
clothing appropriate to the welding job being
performed. Do not wear loose fitting or torn
clothing. Remove all rings from fingers, loose
jewelry, confine long hair and loose clothing
before working on this machinery.
3.
Disconnect the battery and hang a “Do Not
Operate” tag in the operator’s compartment.
remove ignition keys.
4.
If possible, make all repairs with the machine
parked on a level, hard surface. Block the
machine so it does not roll while working on or
under the machine. Hang a “Do Not Operate”
tag in the operator’s compartment.
5.
Do not work on any machine that is supported
only by lift, jacks or a hoist. Always use blocks
or jack stands, capable of supporting the
machine, before performing any disassembly.
00
–1–3
Find manuals at https://best-manuals.com