New Holland CR8.90 Скачать руководство пользователя страница 56

Страница: 56 / 81

Engine - Engine and crankcase

4. Connect the lift chain to a suitable lifting device.

5. Carefully lift the engine above the combine and lower

into position into the frame.

NOTE:

Illustration is for reference only. It may not be the

actual engine.

NOTE:

The lifting device should be rated for at least

907.2 kg

(

2000 lb

). Allow enough clearance to lift the en-

gine from the combine, approximately

907.2 kg

(

2000 lb

)

from the floor.

10013136

6. For safety reasons to the radiator, place a sheet of ply-

wood, cut to size, in front of the radiator for protection.

7. Slide the engine towards the gearbox onto the gear box

input shaft.

8. Align the holes of the gearbox with the engine and hand

start a cap screw

(1)

on each side of the coupling, going

back and forth until all cap screws are installed.

86070283

9. With the engine positioned in the frame, align the two

front mounting holes on the grain tank side. Install the
mounting hardware

(1)

into the mount. Do not tighten

yet.

NHIL15CR00055AA

_47865347 25/04/2015

10.1 [10.001] / 14

Содержание CR8.90


















































































Результаты поиска

Содержание CR8.90

Отзывы:

Похожие инструкции для CR8.90

Бренды по названию

Популярные бренды

New Holland CR8.90, Руководство по обслуживанию

Результаты поиска

Содержание CR8.90

Отзывы:

Похожие инструкции для CR8.90

Бренды по названию

Популярные бренды