NEW ENERGY PV Скачать руководство пользователя страница 17

 

7.9 Do not remove the waterproof rubber rings out of the junction box or connectors. 

7.10  Use of diesel oil for heating is strictly prohibited at installation site, which may lead to 

connector failure because the gas after combustion of diesel and other petroleum products. 

8 Maintenance 

8.1Modules  need to be inspected and maintained regularly,  check all electrical connections to 

ensure that there is no open circuit and well connected. 

8.1.1 Check the open circuit voltage of each module: 

8.1.2 Covered the modules completely by non-transparent material. 

8.1.3 Disconnect the wire terminals 

8.1.4  Remove the non-transparent material off  the modules; check and measure the terminal 

open circuit voltage. 

8.1.5 If the measured voltage is reduced by 1/4, it supposed to be bypass diode damaged. Please 

test the bypass diode performance. 

8.2 It’s recommend that adopt the following maintenance to ensure the modules maintain the best 

performance: 

8.2.1 Check whether the modules have appearance defects: whether the surface of the modules 

are  damaged or abnormal, whether the modules  are occluded by objects, whether the fixing 

between the modules  and the frame  is loose or not, and contact qualified or experienced 

maintenance personnel to adjust or repair after finding the abnormalities. 

8.2.2 Clean modules once a year as much as possible, depending on local conditions. When dirt 

appears on the surface of modules, it will reduce the power generation. When cleaning, a soft 

sponge or a rag can be used to wet the  glass surface of the modules. A mild, non-abrasive 

detergent can be used to remove fouling. The use of corrosive chemical cleaners is strictly 

prohibited. In order to reduce electric shock or burns, it is recommended to clean modules in the 

morning or evening. 

8.2.3  Mechanical and electrical checks are required every six months  to ensure the modules’ 

connectors clean and reliable connected.And ensure good electrical connection and no corrosion. 

8.2.4 It need ask qualified person to check the modules if have any doubt on the modules. 

8.2.5 Please note that all maintenance instructions, such as brackets, charging rectifier, inverters 

Содержание PV



















Отзывы: