background image

 

        TROUBLESHOOTING 

                                                               

WARNING 

     TURN OFF, UNPLUG HEATER AND LET COOL BEFORE SERVICING. 

     

ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND  

     REPAIR HEATER. 

                                                      CAUTION 

    NEVER USE A WIRE, NEEDLE, OR SIMILAR OBJECT TO CLEAN ODS/ 
    PILOT. THIS CAN DAMAGE ODS/PILOT. 
 
OBSERVED                                   POSSIBLE

  

PROBLEM                                    CAUSE                                  SOLUTION 
 

When igniter button is pressed,  1. Igniter electrode positioned   1. Replace igniter 
there is no spark at ODS/PILOT    incorrectly                                                            
                                                    2. Igniter electrode broken         2. Replace igniter  
                                                    3. Igniter electrode not               3. Reconnect igniter cable 
                                                        connected to igniter cable                                                
                                                    4. Igniter cable pinched or wet   4. Free igniter cable if pinched 
                                                                                                            by any metal or tubing. Keep 
                                                                                                            igniter cable dry. 
                                                    5. Broken igniter cable               5. Replace piezo igniter cable. 
                                                    6. Bad piezo igniter                     6. Replace igniter cable 
 

OBSERVED                               POSSIBLE                                SOLUTION 
PROBLEM                                CAUSE                                                                                   
 

When igniter button is pressed,  1. Gas supply turned off or         1. Turn on gas supply or open 
there is spark at ODS/PILOT but    manual shutoff valve is               manual shutoff valve 
no ignition.                                       closed  
                                                    2. Control knob not in “PILOT”  2. Turn control knob to “PILOT” 
                                                        position                                        position  
                                                    3. Control knob not pressed in     3. Press in control knob while in  
                                                        while in “PILOT” position          “PILOT” position.

  

26

Содержание CR8T








































Отзывы: