manualshive.com logo in svg

NEW BRUNSWICK SCIENTIFIC Innova 4300, Руководство по эксплуатации

Поделиться
Скачать
NEW BRUNSWICK SCIENTIFIC Innova 4300 Скачать руководство пользователя страница 38

26 

INNOVA 4300 

•

 M1193-0050 

 

User’s Guide 

5.  Check the belt tension with a light side pressure near the center of the belt.  It 

should deflect approximately 3/8 inch (9.5 mm).  

 
6.  If adjustment is needed, loosen the two nuts holding the motor plate and move the 

plate to either loosen or tighten the belt.  Tighten the nuts when the adjustment is 
correct. 

 
7.  Replace the lower front cover.  
 
8.  Connect the power cord.  
 
9.  Set the circuit breaker to the “ON” position.  
 
The unit is ready for operation. 

 

5.6 

Replacing the Motor Assembly 

 

1.  Turn off the power and disconnect the power cord.   

 

2.  Remove the lower front cover using a Phillips (+) screwdriver.  

 

3.  Remove the connector from the motor assembly (

see Figure 9 below

).  Remove 

the green ground wire going to the chassis (disconnect from the chassis side). 

 

Figure 9:  Motor Assembly Replacement 

 

 

 

Содержание Innova 4300






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды