Neve 1073N Скачать руководство пользователя страница 6

1073N Channel Amplifier

Issue 1.4

Configuring the 1073N for Neve rack or Original BCM10

When the 1073N is used in a Neve 3U or 5U rack or an original BCM10 
console the rear panel

 

input and output connections, power switch, 

fuse and phantom power controls are not used

. The following 

configuration should be used for the remaining controls:

Set ‘

EXT LVL CTRL’ 

switch to 

YES: 

This routes the 1073N audio 

through the volume control of the rack or console.

Set ‘

5k1 TERMINATION’ 

to 

OFF: 

This removes the 5.1k

resistance 

from the signal path to ensure correct frequency response.

Set 

Mic Impedance

 to match the microphones you are using

:

 Low 

impedance = 300

W,

 Hi impedance = 1200

W.

In most cases you would set this to Hi. 

Configuring the 1073N for Neve 45 series consoles including the new 2016 BCM10

When the 1073N is used in a Neve 45 series console without fader 

connections (most 45 series consoles other than the original BCM10) the 
rear panel 

input and output connections, power switch and 

phantom power controls are not used

 the following configuration 

should be used for the remaining controls:

Set ‘

EXT LVL CTRL’ 

switch to 

NO:

 This routes the 1073N audio 

internally.

Set ‘

5k1 TERMINATION’ 

to 

YES: 

This terminates the high pass filter 

correctly to ensure correct frequency response.

 

Set 

Mic Impedance

 to match the microphones you are using

:

 Lo 

impedance = 300

W,

 Hi impedance = 1200

W.

In most cases you would set this to Hi. 

(Rear Panel Controls & Connectors) Quick Configuration Guide

 Stand-alone 

Neve rack/ Original 

BCM 10 

Consoles with no fader 

connection (inc 
BCM10/2 MK2)

EXT LVL CTRL 

NO 

YES 

NO

5k1 TERMINATION 

YES 

NO

YES

MIC I/P Z 

As required 

As required 

As required 

Power switch 

On /Off

Not Used 

Not Used 

48v input 

Connected 

Not Used 

Not Used 

Mic/Line input  (XLR/Jack Combo)

As required 

Not Used 

Not Used 

Line XLR output 

As required 

Not Used 

Not Used 

DI Jack I/P 

As required 

Not Used 

Not Used 

DI PAD switch

As required 

Not Used 

Not Used 

EARTH LIFT switch

As required 

Not Used 

Not Used 

PHANTOM switch

As required 

Not Used 

Not Used 

- 6 -

Содержание 1073N















Отзывы: