manualshive.com logo in svg

Network Technologies NTI SERIMUX-SECURE 8, Инструкция по установке и эксплуатации, Страница: 17 / 79

Поделиться
Скачать
Network Technologies NTI SERIMUX-SECURE 8 Скачать руководство пользователя страница 17

NTI RACK MOUNT CONSOLE TERMINAL WITH CONSOLE SWITCH 

 

12

 

3.1  Administrator Controls 

3.1 1 Login as the administrator  

 

1.

 

The TERMINAL must first be configured (and is typically delivered preconfigured) as described on page 8 under "Getting 
Started”.    

Note:   The administrator can only login from the TERMINAL connection (serially).   Be sure that the Ethernet Mode is set 
to OFF (page 9) before trying to login as administrator.  

2.

 

Press [ Enter ] on the keyboard and the port will open to the "Accessible host list" for "User01", logged in at "Port00".     

3.

 

Press [Esc] to logout,  and [Y] to confirm.     A message will be displayed "Disconnecting user now" 

4.

 

Press [Spacebar] or [Enter].      A prompt requesting a Username will appear. 

5.

 

Enter 

ADMINISTRATOR

 or 

ROOT

 (all capital letters) and press [Enter].   A prompt for a password will appear. 

6.

 

Enter 

NTI

 (all capital letters) and press [Enter].    The Administrator main menu will appear for user ROOT on port 0.  

 

Note:  This will only enter the administrator mode if the administrator password has not yet been changed from "NTI".  

FYI:  If SERIMUX is not at initial power-ON, omit steps 2 and 3 above to login.   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

                                                                   Figure 7- Administrator main menu

 

FYI: The Administrator main menu will also appear if a user with administrative privileges presses [4] from the User main 
menu. 

From the Administrator main menu, the following options are possible

: 

 

Function 

Description 

Keystroke 

Port List 

Display the port list 

[1] 

Port settings 

View or modify any port settings 

[2] 

Port disconnect 

Disconnect any port and logout the user logged in or connected to the port 

[3] + [port 

number] 

User list 

Display the user list 

[4] 

User settings 

View or modify user settings  

[5] 

User disconnect/logout 

Disconnect and logout any user connected to a port 

[6] 

Advanced settings 

View or modify advanced administrative settings (pg 17) 

[7] 

Return to user menu 

Leave the administrative menu and return to the User main menu 

[9] 

Logout 

Logout from SERIMUX 

[0] 

 
 

Содержание NTI SERIMUX-SECURE 8
















































































Отзывы:

Нет отзывов