background image

How to use Z809B

Dimmer

Z809B is only suitable for dimming use. Application such as light level control is applicable
where dimmable light bulbs are used. Non-dimmable light bulbs are not to be used with
this device as the dimming effect will not be obvious.

Remote control

When the device has joined to the network and paired (see

Device pairing for

On/Off/Level control)

with a remote controller the device is ready to be used. Z809B

should now be able to responds to on, off, level control command from a wireless remote
controller.

Operation:

If the Z809B device is properly paired with a switch device, you should see

Z809B respond to on or off instruction wirelessly.

When the Off button is press twice and then press On button once, Z809B will stay Off.
This is to prevent from accidental turning the device on.

Manual switch

When the button switch is pressed, Z809B increases the output by 1/8

th

. As you keep

pressing until it passes the brightest, Z809B will decrement the output until its output is
totally turned off.
The On/Off status indicator turns

red

when the output is totally Off or

green

when output is

On.

Absent of Coordinator Indication

A ZigBee network required a coordinator to maintain network and other services. Z809B
would indicate to the user of whether the coordinator is present or is within the effective
signal transmission by means of LED indication.
After Z809B joined to a network, it checks once every 10 minutes for the coordinator. After
3 detecting attempts that the coordinator is not within the effective range, its network
indicator will flash 30 times in

green

. In the normal operation, the network indicator stays

solid

green

without flashing.

Содержание Z809B














Отзывы: