Netis WF-2403 Скачать руководство пользователя

Страница: 58 / 59

Portable Wireless-N Router/AP

User Manual

6.2.

I forget Password (Reset the Router without Login)



Use a pencil to press the button for about 2-6 seconds when it is working, then leave your

hands, it will restore settings to the factory configuration. The default password is

guest

6.3.

I have some problems related to Connection with Cable Modem

Please follow the following steps to check the problems:



Check whether the DSL modem works well or the signal is stable. Normally there will be

some indicator lights on the modem, users can check whether the signal is ok or the

modem works well from those lights. If not, please contact the ISP.



Check the front panel of the Router, there are also some indicator lights there. When the

physical connection is correct, the Power light and the CPU light should be solid; the

WAN light should be blinking. If you use your computer, the corresponding LAN port

light should be blinking too. If not, please check whether the cables work or not.



Repeat the steps in

WAN Setup

Connect with Internet through DSL Modem.

6.4.

I can browse the router’s Web-based Configuration Utility but cannot access

the Internet.



Check if the WAN LED is ON. If not, verify that the physical connection between the

router and the DSL/Cable modem is firmly connected. Also ensure the DSL/Cable modem

is working properly.



If WAN LED is ON, open the System Overview page of the Web configuration utility and

check the status group to see if the router’ s WAN port has successfully obtained an IP

address.



Make sure you are using the correction method (Dynamic IP Address, PPPoE, or Static IP)

as required by the ISP. Also ensure you have entered the correct settings provided by the

ISP.



For cable users, if your ISP requires a registered Ethernet card MAC address, make sure

you have cloned the network adapter’ s MAC address to the WAN port of the router. (See

the

MAC Address

field in

WAN Setup

6.5.

My wireless client cannot communicate with another Ethernet computer.



Ensure the wireless adapter functions properly. You may open the Device Manager in

Windows to see if the adapter is properly installed.



Make sure the wireless client uses the same SSID and security settings (if enabled) as the

Содержание WF-2403




























































Результаты поиска

Содержание WF-2403

Отзывы:

Похожие инструкции для WF-2403

Бренды по названию

Популярные бренды

Netis WF-2403, Руководство пользователя

Результаты поиска

Содержание WF-2403

Отзывы:

Похожие инструкции для WF-2403

Бренды по названию

Популярные бренды