NETGEAR ProSafe GSM7324 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 263

NETGEAR ProSafe GSM7324 Скачать руководство пользователя страница 143

7000 Series L3 Managed Switch Reference Manual for Software v1.0

Routing Commands

8-15

May 30, 2003 Beta Draft

Area LSA Count

Total number of link-state advertisements in this area's link-state
database, excluding AS External LSA's.

Area LSA Checksum

A number representing the Area LSA Checksum for the specified
AreaID excluding the external (LS type 5) link-state advertise-
ments.

Stub Mode

Represents whether the specified Area is a stub area or not. The
possible values are enabled and disabled. This is a configured
value.

Import Summary LSAs
Metric Value

Is a number representing the Metric Value for the specified area.

Metric Type

Is the Default Metric Type for the specified Area.

show router ospf area range

This command displays information about the area ranges for the specified <areaid>. The <areaid>
identifies the OSPF area whose ranges are being displayed.

Format

show router ospf area range

<areaid>

Area ID

Is the area id of the requested OSPF area.

IP Address

Is an IP Address which represents this area range.

Subnet Mask

Is a valid subnet mask for this area range.

Lsdb Type

Is the type of link advertisement associated with this area range.

Advertisement

This indicates whether the advertisement status is enabled or dis-
abled.

config router ospf area range create

This command creates a specified area range.

The <ipaddr> is a valid IP address.

The <subnetmask> is a valid subnet mask.

The [summ] is the lsdb type and is optional.

The [enable/disable] indicates advertise mode and is optional.

«
...
141
142
143
144
145
...
»

Содержание ProSafe GSM7324








































































































































































































































































Отзывы:

Нет отзывов