NETGEAR Nighthawk RS400 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 184

background image

45°

45°

We recommend that the center antenna be vertical and that you aim the others
outward at 45-degree angles, as shown.

LEDs and buttons on the top panel

The status LEDs and buttons are located on the top of the router.

Table 1. LED and button descriptions

Descriptions

LEDs and Buttons

Solid amber. The router is starting.
Blinking amber. The firmware is upgrading, or the Reset button was pressed.
Solid white. The router is ready.
Blinking white. The firmware is corrupted.
Off. Power is not supplied to the router.

Power

Solid white. The Internet connection is ready.
Solid amber. The router detected an Ethernet cable connection to the modem.
Blinking white. The port is sending or receiving traffic.
Off. No Ethernet cable is connected between the router and the modem.

Internet

Solid white. The 2.4 GHz WiFi radio is operating.
Blinking white. The router is sending or receiving WiFi traffic.
Off. The 2.4 GHz WiFi radio is off.

2.4 GHz WiFi

Solid white. The 5 GHz WiFi radio is operating.
Blinking white. The router is sending or receiving WiFi traffic.
Off. The 5 GHz WiFi radio is off.

5 GHz WiFi

Solid white. A USB storage device is connected and is ready.
Blinking white. A USB storagedevice is plugged in and is trying to connect.
Off. No USB storagedevice is connected, or someone clicked the Safely Remove
Hardware button and it is now safe to remove the attached USB storage device.

USB 3.0 (front panel)

Solid white. A USB device is connected and is ready.
Blinking white. A USB device is plugged in and is trying to connect.
Off. No USB device is connected, or someone clicked the Safely Remove Hardware
button and it is now safe to remove the attached USB device.

USB 2.0 (rear panel)

User Manual

11

Hardware Setup

Nighthawk AC2300 Cybersecurity WiFi Router Model RS400

«
...
9
10
11
12
13
...
»

Содержание Nighthawk RS400

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nighthawk RS400

Бренд: Ubee Страницы: 9

Бренд: BSD Networks Страницы: 7

Бренд: UHP Страницы: 15

Бренд: Ubiquiti Страницы: 21

Бренд: Infoblox Страницы: 13

Бренд: Waver Страницы: 36

Бренд: Buffalo Страницы: 2

Бренд: H3C Страницы: 68

Cyclades CS4008

Бренд: Avocent Страницы: 2

Бренд: AMG Страницы: 4

ServCon FPS-3003

Бренд: LevelOne Страницы: 45

Бренд: XtendLan Страницы: 54

Бренд: Matrix Switch Corporation Страницы: 48

Бренд: Lantech Страницы: 23

Бренд: H3C Страницы: 4

Бренд: BinTec Страницы: 35

Бренд: H3C Страницы: 4

Network Controller

Бренд: MikroTik Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды