NETGEAR Nighthawk AX6 AX4300 Скачать руководство пользователя

Страница: 111 / 162

To erase the settings:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Administration > Backup Settings.

The Backup Settings page displays.

5. Click the Erase button.

The configuration is reset to factory default settings. When the reset is complete,
the router restarts. This process takes about two minutes.

WARNING:

To avoid the risk of corrupting the firmware, do not interrupt the reset.

For example, do not close the browser, click a link, or load a new page. Do not turn
off the router. Wait until the router finishes restarting.

User Manual

111

Manage Your Router

Nighthawk AX6 6-Stream AX5400 WiFi Router

Содержание Nighthawk AX6 AX4300



































































































































































Результаты поиска

Содержание Nighthawk AX6 AX4300

Отзывы:

Похожие инструкции для Nighthawk AX6 AX4300

Бренды по названию

Популярные бренды

NETGEAR Nighthawk AX6 AX4300, Руководство пользователя

Результаты поиска

Содержание Nighthawk AX6 AX4300

Отзывы:

Похожие инструкции для Nighthawk AX6 AX4300

Бренды по названию

Популярные бренды