background image

 

 

HyPer 9HV IS User Manual Version 06

 

NetGain Motors, Inc.

 

Page 14 of 28

 

 

20.

 

On the motor encoder’s 4 Pin Ampseal connector - ensure the wires and connectors are restrained from 
movement within the installation area. Also ensure that these wires do not intersect or contact High 
Voltage cables or the motor’s field. Verify correct 

wiring of the encoder

1.

 

PIN1 is connected to K1-35  (+5V Out). 

2.

 

PIN2 is connected to K1-21 (Encoder Sin 1). 

3.

 

PIN3 is connected to K1-33 (Encoder Cos 1). 

4.

 

PIN4 is connected to K1-9  (Encoder I/O Ground). 

 

21.

 

Check that accessory voltage (12-24V) is connected to K1-24 (Key Switch In) when switching on the 
Key. This is the only wire on connector K1 that will see voltage from an outside source. 
 

22.

 

Check that Contactor Positive Coil is connected to K1-25 (Coil Return). 
 

23.

 

Check that Contactor Negative Coil is connected to K1-26 (Driver Output 1). 
 

24.

 

Connect Amp 35 pin connector to controller plug K1. 
 

25.

 

Couple the supplied 

Null Modem

 Serial Cable to the supplied Serial-USB adapter.  

 

26.

 

Connect USB end to PC loaded with SME Smartview Smarview Sys software.  
 

27.

 

Connect female serial end to X144 controller’s male serial K3 port.  
 

28.

 

Open 

SmartView DLR Sys

 software. 

 

29.

 

Select Connection type: Normal or Wired. Then select the Serial Port your device driver was installed 
on. 

1.

 

Your COM port number set is listed in the Windows Device Manager.  

2.

 

Verify that the COM port number is not already used by another software when SmartView is 
opened. 
 

30.

 

Verify vehicle is in Neutral with wheels suspended from the ground. Then switch on X144 controller via 
Key Switch, and ensure the controller’s Green or Red Status light is solid or blinking.  

1.

 

If Controller’s Status light is off, verify wiring.  

2.

 

If Smartview’s home screen options do not appear with a “Manage” block, verify steps 11-15 
are followed in order. 
 

31.

 

Once communicating with the Controller, install the downloaded 

.bin

 Firmware by clicking on: 

1.

 

Mange        Clone         Firmware Update 

2.

 

Browse the Firmware Path and select the most recent Firmware release, which you have 

downloaded

3.

 

Once this .bin file is selected and in the Firmware Path, Click 

PROGRAM.

 

 

32.

 

 Install your motor’s downloaded clone file by clicking on: 

Содержание HyPer 9HV IS





























Отзывы: