NetComm NCT-1000 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 139

NetComm NCT-1000 Скачать руководство пользователя страница 46

46

NCT-1000/NCT-1020 User Guide

YML836 Rev2

5.1 System

The sections that follow are accessed from the system screen of the AMCU main control unit.

5.1.1 Conﬁguration

The

Conﬁguration

tab conﬁgures IGMP Snooping, Broadcast Control, and Priority Queue Service.

IGMP Snooping

Note:

If you want to connect the ASTU card, set the IGMP Snooping to Enable (default setting)
ﬁrst.

ASTU supports private VLAN or private/tagged VLAN simultaneously. AAT24A supports either private or
tagged VLAN. Please DO NOT switch the VLAN mode while the ASTU card is connected as this will cause an
unpredictable operational problem.

The default of IGMP Snooping is enabled. To disable it, choose

Disable

and click

Set

to apply the setting.

IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to report their multicast group
memberships to any immediately neighboring multicast routers. Enabling IGMP snooping allows the ports to
detect IGMP queries and report packets and manage IP multicast trafﬁc through the IP DSLAM to avoid trafﬁc
ﬂooding.

«
...
44
45
46
47
48
...
»

Содержание NCT-1000












































































































































Отзывы:

Нет отзывов