background image

| Industrial 

IoT

20

Electrostatic discharge (ESD)

Do not touch the SIM card’s metal connectors.

Air Bags

Do not place the device in the area near or over an air bag or in the air bag deployment area

Mount the device safely before driving your vehicle.

Emergency & other situations requiring continuous connectivity

This device, like any wireless device, operates using radio signals, which cannot guarantee 
connection in all conditions. Therefore, you must never rely solely on any wireless device for 
emergency communications or otherwise use the device in situations where the interruption of data 
connectivity could lead to death, personal injury, property damage, data loss, or other loss.

Device heating

Your device may become warm during normal use.

Faulty and damaged products

Do not attempt to disassemble the device or its accessory.

Only qualified personnel should service or repair the device or its accessory.

If your device or its accessory has been submerged in water or other liquid, punctured, or 
subjected to a severe fall, do not use it until you have taken it to be checked at an authorised 
service centre

Interference

Care must be taken when using the device in close proximity to personal medical devices, such 
as pacemakers and hearing aids.

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 15cm be maintained 
between a device and a pacemaker to avoid potential interference with the pacemaker.

Hearing aids

People with hearing aids or other cochlear implants may experience interfering noises when 
using wireless devices or when one is nearby.

Содержание NTC-223

























Отзывы: