NetApp AFF A200 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 79

background image

Steps

1. If you are not already grounded, properly ground yourself.

2. Locate the RTC battery.

3. Gently push the battery away from the holder, rotate it away from the holder, and then lift it out of the

holder.

Note the polarity of the battery as you remove it from the holder. The battery is marked with
a plus sign and must be positioned in the holder correctly. A plus sign near the holder tells
you how the battery should be positioned.

4. Remove the replacement battery from the antistatic shipping bag.

5. Locate the empty battery holder in the controller module.

6. Note the polarity of the RTC battery, and then insert it into the holder by tilting the battery at an angle and

pushing down.

7. Visually inspect the battery to make sure that it is completely installed into the holder and that the polarity is

correct.

Step 4: Reinstall the controller module and set time/date after RTC battery replacement

After you replace a component within the controller module, you must reinstall the controller module in the
system chassis, reset the time and date on the controller, and then boot it.

Steps

1. If you have not already done so, close the air duct or controller module cover.

75

«
...
75
76
77
78
79
»

Содержание AFF A200
















































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A200

Бренд: Megatank Страницы: 12

Бренд: Quantum Страницы: 312

Бренд: Kanguru Страницы: 12

Бренд: LaCie Страницы: 37

Бренд: eazished Страницы: 12

Бренд: Frontier Страницы: 9

Бренд: Icy Box Страницы: 24

Бренд: HGST Страницы: 51

Бренд: Seagate Страницы: 36

Бренд: Netstor Страницы: 11

TS-h2483XU-RP Series

Бренд: QNAP Страницы: 12

Бренд: Ultra Products Страницы: 1

Deskstar T7K500

Бренд: Hitachi Страницы: 2

DKC-F710I-1R6FM

Бренд: Hitachi Страницы: 3

Бренд: Hitachi Страницы: 6

Бренд: Hitachi Страницы: 1

Бренд: Hitachi Страницы: 1

External USB Storage

Бренд: Hitachi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды