NetApp AFF A200 Скачать руководство пользователя страница 58

Страница: 58 / 79

If the system-level
diagnostics tests…

Then…

Were completed without
any failures

a. Clear the status logs:

sldiag device clearstatus

b. Verify that the log was cleared:

sldiag device status

The following default response is displayed:

SLDIAG: No log messages are present.

c. Exit Maintenance mode:

halt

The controller displays the LOADER prompt.

d. Boot the controller from the LOADER prompt:

bye

e. Return the controller to normal operation:

If your controller is in an HA pair

, perform a give back:

storage

failover giveback -ofnode

replacement_node_name

If you disabled automatic giveback, re-enable it with the

storage failover modify

command.

If your controller is in a stand-alone configuration

, proceed to the next

step. No action is required.

You have completed system-level diagnostics.

Содержание AFF A200
















































































Результаты поиска

Содержание AFF A200

Отзывы:

Похожие инструкции для AFF A200

Бренды по названию

Популярные бренды

NetApp AFF A200, Руководство пользователя

Результаты поиска

Содержание AFF A200

Отзывы:

Похожие инструкции для AFF A200

Бренды по названию

Популярные бренды