Net Optics 10/100/1000 Base Tap Скачать руководство пользователя страница 7

Gig Zero Delay Tap & 10/100/1000BaseT Tap

4

About This Guide

This guide explains how to install the Gig Zero Delay Tap and the 

10/100/1000BaseT Tap. Please read the Guide before attempting to install 

the device.

This guide covers the following models: 
•  TP-CU3-ZD 

10/100/1000 Tap with Zero Delay

•  TP-CU3-ZD-DC  10/100/1000 Tap with Zero Delay, -48V DC power

•  TP-CU3 

10/100/1000 Tap

•  TP-CU3-DC 

10/100/1000 Tap , -48V DC power

Unpacking and Inspection

Carefully unpack the Gig Zero Delay Tap and check for damaged or   missing 

parts. The Tap ships with the following:

•  (1) Tap device

•  (2) power supplies (TP-CU3-ZD and TP-CU3 only)

•  (2) power cords (TP-CU3-ZD and TP-CU3 only)

•  (1) retainer clip (TP-CU3-ZD and TP-CU3 only)

•  (1) network cable, 3 meter, straight-through (purple) 

•  (1) network cable, 3 meter,  cross-over (green)

•  (2) monitor cables, 3 meter, straight-through (purple)

•  (1) Installation Guide

You may have also ordered a panel for rack mounting and an extended warranty. 

Carefully check the packing slip against parts received. If any part is missing or 

damaged, contact Net Optics Customer Service immediately.

Warning! ____________________________________________________________

For the TP-CU3-ZD and TP-CU3 models, use only the power supplies pro-

vided by Net Optics for use with this product. Use of other power supplies may 

result in a safety hazard that could cause damage or injury.

_______________________________________________________________________

Содержание 10/100/1000 Base Tap





















Отзывы: