background image

6

sleeP

Sets the detector’s re-trigger interval.

2sec

 The detector will “sleep” for 2 seconds 

after being triggered. 

 

This  mode  should  only  be  used  for 
walk-testing coverage as it will reduce 
the battery life if left on permanently.

2min

 Normal operating mode. The detector 

will  “sleep”  for  2  minutes  after  being 
triggered. (Default) 

This battery-saving mode limits unwanted radio 
transmissions  by  waiting  until  there  has  been 
no detectable movement in the area for at least 
2  minutes  before  it  will  trigger  and  transmit  a 
new alarm.
The Sleep time applies only to alarm transmis-
sions.  The  night-light  will  turn  on  every  time 
the  detector  detects  movement  (if  enabled  by 
the LIGHT switch and if the ambient lighting is 
suitably low).

lIght level

Sets the light level at which LUX’s ambient light 
sensor will enable the night-light.

DRK

  The  night-light  will  operate  only  when 

the ambient lighting is very low or near 
total darkness. (Default)

LHT

  The  night-light  will  operate  when  the 

ambient lighting is semi-dark.

settIngs

Ness LUX custom settings are set by turning dipswitches 1-6 on or off. The dipswitches are easily ac-
cessible by removing LUX from the back housing.
Use a small screwdriver or pen tip to set the switches.

lIght

Enable/Disable the night-light.

ON

  The  night-light  will  function  and  draw 

power from battery A. (Default)

OFF

 The night-light is disabled.

Note: If battery A is not installed or is flat the night-
light will not work regardless of the switch setting.

alarM led

Enable/Disable the blue Alarm LED.
Note. The blue LED will always operate in Test 
Mode regardless of this switch setting.

ON

 The Alarm LED is enabled. (Default)

OFF

 The Alarm LED is disabled.

Pulse

Sets the detector’s pulse count.

1–2

 1–2 Pulses or walk steps should cause 

an alarm. (Default)

3–4

 3–4 Pulses or walk steps should cause 

an alarm. 

 

this setting is recommended for one 
pet over 10kg or multiple pets of any 
size.

range

Sets the maximum detection range.

HI

 15m x 15m max. coverage.

LOW

  12m  x  12m  max.  coverage.  recom-

mended setting. (Default)

2sec 2min SLEEP

DRK

LHT LIGHT LEVEL

ON

OFF LIGHT

ON

OFF ALARM LED

1-2

3-4 PULSE

HI

LOW RANGE

Содержание Lux









Отзывы: