Neptune NXP-M Скачать руководство пользователя страница 17

Installing the Dosing Pump

Installation examples

17

Subject to technical changes.

Stepper motor-driven diaphragm dosing pump NXP-M and NXP-P

Operating instructions

7 Installing the Dosing Pump

DANGER

Mortal danger from electric shock!

Electrically conductive liquid can enter pump housings, cable screw 
connections and mains connectors.

ð 

Make sure that all protective measures comply at least with the 
requirements of protection class IP65.

ð 

Always set up the dosing pump such that water cannot enter the 
housing.

CAUTION

Danger of personal injury and material damage!

A dosing pump that is difficult to access represents a danger due to 
incorrect operation and faulty maintenance.

ð 

Install the dosing pump such that it is accessible at all times. 
Especially the oil level glass, the oil inlet and the oil drain.

7.1  Set up information

When installing, follow the basic principles below:

The valves must be vertical: Discharge valve at top, suction valve at 
bottom. in this connection, pay attention to the arrow on the dosing 
head. The dosing head must be aligned such that the arrow points 
vertically upwards.

You should install the dosing pump at a convenient height for 
operation.

It must not be installed under the ceiling.

The frame of foundation for fixing the dosing pump must not be 
subjected to jolts. The pump must be vibration-free and stable.

There must be enough free space in the area of the dosing head and 
the suction and discharge valves for these parts to be easily 
dismantled if required. The entire space requirement for installation 
and maintenance is approximately 1 m².

The distance from the sides of the dosing pump to the wall or other 
dosing pumps or equipment must be at least 3 cm. There must be a 
guaranteed flow of circulating air.

The maximum ambient temperature must be complied with, see 
chapter 5.2 “Operating conditions and limits“ on page 13. If 
necessary, radiant heat from surrounding equipment must be 
screened.

Avoid exposure to direct sunlight.

The dosing pump is not intended for use out of doors unless 
appropriate protective measures have been taken to prevent dust and 
water from entering the housing.

For the dimensions of the fastening holes, refer to chapter 6 
“Dimensions“ on page 15.

The tightening torque for the fastening bolts is 1.5 – 2 Nm.

7.2  Installation examples

7.2.1  Installation on a wall console

Fig. 10:  Installation on a wall console

To reduce the structure-borne noise, the dosing pump is bolted to the wall 
bracket using rubber elements. The materials necessary for this are 
included with the wall bracket.

7.2.2  Installation on the wall

Fig. 11:  Installation on the wall

The dosing pump can be mounted to the floor or directly to the wall 
without the need for additional elements. Turn the dosing head appropri-
ately to ensure the flow direction of the medium through the dosing head.

Содержание NXP-M













































Отзывы: