Neptune 7000 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 25

background image

7

SECTION I

PARTS ORDERING INSTRUCTIONS

The complete model number and serial number of the pump must be furnished to insure

prompt and accurate parts service. These numbers are found on the name plate (sample

below) located on the back cover of the pump.

Please refer to page number (17), (18), (19), (20) for parts list. Ballooned drawing of the

pumps can be found on pages (13), (14), (15), (16) and (20).

Spare Parts Kits are found on pages 22 and 23.

Send all orders or inquiries for parts to:

Parts Department

Neptune Chemical Pump Company, Inc.

295 DeKalb Pike

North Wales, PA 19454

Tel.: 215-699-8700

1 -888-3NEPTUNE (888-363-7886)

FAX: 215-699-0370

Web: www.Neptune1.com

Email: [email protected]

NOTE:

PLEASE SUPPLY BOTH MODEL AND SERIAL NUMBERS.

«
...
6
7
8
9
10
...
»

Содержание 7000 Series


























Отзывы:

Нет отзывов

Похожие инструкции для 7000 Series

Бренд: 4rain Страницы: 44

Бренд: Gardena Страницы: 16

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Бренд: SereneLife Страницы: 10

Ingenio VM 050 D400-3-E

Бренд: Atlantic Страницы: 69

Signature XP19-024

Бренд: Lennox Страницы: 32

Бренд: ProMinent Страницы: 81

Бренд: vacuubrand Страницы: 80

Бренд: DAB Страницы: 41

Бренд: Nagman Страницы: 15

Бренд: Flux Страницы: 80

Бренд: AQUASYSTEM Страницы: 12

Serve Better CP-RP

Бренд: Server Страницы: 8

Бренд: Flo Fab Страницы: 9

Бренд: Flotec Страницы: 20

Бренд: WAGNER Страницы: 120

Бренд: Graco Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды