Neol ePowerSwitch M8 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 27

Neol ePowerSwitch M8 Скачать руководство пользователя страница 12

Quick Start Guide ePowerSwitch 8 M/S (M8 / S8) V.11/2006 Page

12

NETWORK PARAMETERS SETTINGS MENU

Command /NP

This menu contains the commands for specifying the network settings (IP address, subnet
mask, gateway and port number) and for permitting or denying the configuration over a local
area network using the ePowerSwitch Finder program.

NETWORK PARAMETERS SETTINGS

MAC Address 00.01.9A.F1.00.0F
1. IP Address 192.168.100.100
2. Subnet Mask 255.255.255.0
3. Gateway 0.0.0.0
4. Port 80
5. Finder Activated

Enter Selection or <ESC> to exit

>

Command 1

NETWORK PARAMETERS SETTINGS

IP Address is: 192.168.100.100

Enter IP Address or <ESC> to exit
You must restart the device (Command /RS) to valid the new parameters

>

Command 2

NETWORK PARAMETERS SETTINGS

Subnet Mask is: 255.255.255.0

Enter subnet mask or <ESC> to exit
You must restart the device (Command /RS) to valid the new parameters

>

Command 3

NETWORK PARAMETERS SETTINGS

Gateway is: 0.0.0.0

Enter gateway address or <ESC> to exit
You must restart the device (Command /RS) to valid the new parameters

>

«
...
10
11
12
13
14
...
»

Содержание ePowerSwitch M8




























Отзывы:

Нет отзывов