3
EN
INSTRUCTION MANUAL
REMOTE POWER FAN 40 CM
90-004
NOTE: BEFORE THE EQUIPMENT IS USED FOR THE FIRST TIME,
READ THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE
REFERENCE.
DETAILED SAFETY REGULATIONS
a) This equipment may be used by children at least 8 years old and by persons
with reduced physical and mental abilities and persons who are not familiar with the
equipment, if supervision or instruction regarding the use of the equipment in a safe
manner is provided so that the threats were understandable. Children should not play
with the equipment. Unattended children should not clean or maintain the equipment.
b) Before removing the cover, make sure that the fan is disconnected from the power
supply.
WARNING
! The device is used for indoor work.
Warning
:
1. Do not insert your fingers or other objects into the grille or movable parts
when the fan is running.
2. Do not place the fan near window curtains or on uneven floors.
3. Avoid places with gas, gasoline and those that threaten the fan
getting wet.
4. In the event of unusual noises or other irregularities in operation,
immediately remove from use and return the fan to the manufacturer or
an authorized repair service.
5. If the supply cord is damaged, it has to be replaced by the manufacturer,
service representative or similarly qualified person in order to avoid
threats.
6. Do not attempt to disassemble or repair the fan in case of its incorrect
work. Send the fan to an authorized service center for repair.
7. This fan is not intended for use by people (including children) with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge unless they have been given supervision or instruction
concerning use of the fan by a person responsible for their safety.
8. Children should be supervised so that they can not play with the fan.
9. After assembling the fan, do not remove the grille.
10. Disconnect the fan from the power source before cleaning or maintenance.
It it is necessary to remove the grille for cleaning or maintenance, make
sure that the fan propeller does not move and fan has been disconnected
from power source.
11. Replacement of a part of a safe suspension system should be entrusted
to the manufacturer, his service representative or a person with
appropriate qualifications.
12. Fastening to the wall, e.g. through hooks and other means, should
withstand four times the weight of the wall fan.
13. Attaching the suspension system should be entrusted to the manufacturer,
his service representative or a person with appropriate qualifications.
WARNING
: If suspicious oscillation is visible, immediately turn off the fan and do not use it,
contact the manufacturer, his service representative or a suitably qualified person.
Maintenance
:
1. Unplug the fan from the socket.
2. Remove dust from the outside of the fan with a soft cloth.
3. To remove the front grille, unscrew the securing screws located on the edge of the grill.
4. Wipe dust off the grilles and blades with a soft cloth. Note - Do not wet
the cloth too much so that it does not form dripping drops, it may limit
the fan insulation.
5. When cleaning the blades, do not use too much force, deformation of the blade will
affect the balance.
6. The fan should be assembled in reverse order to removal. If this is not
possible, do not use force. Send the fan to the manufacturer or
a designated service center as soon as possible to check the device.
7. Before start, the propeller guard must be tightened securely with the mounting screws.
8. Run for 5 minutes. Check that the fan is working properly. Maintenance is complete.
Explanation of the pictograms used
1
2
3
1. Read the operating manual, observe the warnings and safety conditions contained in it!
2. Disconnect the device before repair.
3. Protect the device against moisture.
PARTS NAME
1. Front grill
2. Blade,
3. Back Grill,
4. Motor,
5. Pillar,
6. Base.
1.
2.
3.
4. 5. 6.
PANEL STEROWANIA
1
2
4
5
3
1 - Speed select: Lo(Low)/
Mi(Middle)/Hi(High)
2 - Wind type: Na(Nature)/Ge(General)/
Sl(Sleep)
3 - Timer: 0.5H-7.5H
4 - Oscillation ON/OFF
5 -Power ON/OFF
REMOTE CONTROL
Power
Time
Speed
Swing
Wind type
1
2
4
5
3
1 - Power ON/OFF
2 - Timer : 0.5H-7.5H
3 - Oscillation ON/OFF
4 - Speed select: Lo(Low)/Mi(Middle)/
Hi(High)
5 - Wind type: Na(Nature)/Ge(General)/
Sl(Sleep)
ASSEMBLY INSTRUCTION
1. Assemble the Pillar on the Base.
2. Assemble the Motor on the Pillar.
neo-tools.com
neo-tools.com
