Nemco 9100 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 11

Nemco 9100 Скачать руководство пользователя страница 9

Page | 9

P: 419.542.7751 F: 419.5426690 800.782.761 nemcofoodequip.com

Troubleshooting/Error Codes

Flashing
Display
Indication

Cause

Solution

U

No pan or non- induction pan

Place an appropriate pan on the
cooktop target

1

Over current

Check for abnormal conditions like
water, moisture or broken parts or
cord. Unplug the unit. Plug it back in.
If the error continues, contact
customer service.

2

Over Voltage

Check to verify that the outlet voltage
is correct and within limits. Unplug
the unit. Plug it back in. If the error
continues, contact customer service.

3

Under Voltage

Check to verify that the outlet voltage
is correct and within limits. Unplug
the unit. Plug it back in. If the error
continues, contact customer service.

4

Main Heat Sink Over Temp

Check to verify that the fans are
working. Check to make sure the air
flow is unrestricted.

5

External Temp. Probe problem

Temp mode not available on Drop-In
series.

6

Pan is Overheated

Make sure the pan is not empty.
Allow the unit to cool down.

7

Power Frequency is Unstable

Check the incoming power for
frequency stability. Unplug the unit.
Plug it back in. If the error continues,
contact customer service.

8

OP Amp Offset Error

Unplug the unit. Plug it back in. If the
error continues, contact customer
service.

9

Main Coil Overcurrent

Unplug the unit. Plug it back in. If the
error continues, contact customer
service.

«
...
7
8
9
10
11
»

Содержание 9100












Отзывы:

Нет отзывов