background image

 

 

 

 

How to use 

The mode select switch 

The mode selection switch is used to select between RS-232 control mode and the Auto on/off mode combined with 
one of the three EQ presets (Video Conference, Music & Present).

 

 

Auto On/off mode 

When the switch is set in one of the three Auto on/off modes the Sound Bar will activate the Wake-on-signal 
function and work autonomously powering on and off as described in “Wake-on-signal” chapter on page 10.

 

 

Setting the switch in Auto on/off mode will ensure that Wake-on-signal is activated even if Wake- on-signal 
previously have been disabled by a command in RS-232 mode.

 

 

In Auto on/off mode the RS-232 control port will still be active, but the Sound Bar will not react to incoming 
commands or queries. Instead, the Sound Bar will reply to a RS-232 command or query telling the connected 
control system that the Sound Bar is set to Auto on/off mode.

 

 

RS-232 mode 

In RS-232 mode, the RS-232 port will be active. The RS-232 port is used to control the Sound Bar by 
commands and status from Sound Bar can be requested by queries.

 

 

The Wake-on-signal function will by default be disabled in RS-232 mode. But by RS-232 command it is possible to 
activate the function if both Wake-on-signal and RS-232 control is needed for the application.

 

 

To control the Sound Bar by RS-232 connect a control system to the RS-232 port with the following 
settings:

 

 

 

Baudrate: 19.200 

 

Databit: 8 

 

Stopbit: 1 

 

Parity: None 

 

Please be aware that RS-232 control is deactivated if the Sound Bar is set to Auto on/off mode. The commands 
for RS-232 control can be found on page 12.

 

 

When changing the mode switch from “Auto on/off” to “RS232” the Sound Bar will automatically apply 
the following settings: 

 

Power = ON 

 

Mute = OFF 

 

Volume = 70 (If max volume is set lower than 70, then that will not be exceeded) 

 

Input = 1 (RCA Unbalanced)  

 

Wake on signal = OFF 

 

EQ setting = Video Conference.

Содержание SB2















Отзывы: