4
•
Do not use the product when the cable or plug is damaged.
•
Make sure that the electrical supply in your area matches a
voltage of 220 – 240 VAC and a frequency of 50 Hz.
•
Connect to a grounded socket only.
•
If necessary, use an earthed extension cable of a suitable
diameter.
•
Fully extend the power cord and make sure the power cord does
not contact the product.
•
When using an extension cord, use one which is as short as
possible and fully extended.
•
Do not let the power cable touch hot surfaces.
•
Do not close a door on the power cable.
•
Do not pull the power cable to move the product.
•
Do not put any objects into openings. Do not use with any
opening blocked.
•
Do not use the product without the air inlet and outlet covers in
place to avoid touching hot and moving parts that may cause
injuries.
•
Do not drink water from the product. This may cause illness.
•
Be aware that the refrigerants should be odourless.
•
The refrigerants should be added by the manufacturer, its service
agent or similar qualified persons.
•
Do not use the product in temperatures below 0˚C.
•
Do not expose the product to direct sunlight or rain.
•
Do not spill any water on the product.
•
Do not sit on the product.
•
Unplug the power cable when the product is not in use for a long
time.
•
Do not unplug the product by pulling on the cable. Always grasp
the plug and pull.
•
Do not block the air in- and outlets of the product.
•
Only install, operate and store the product in a room with a floor
area above 4 m
2
.
•
Only store the product in a well-ventilated area.
•
Do not use external timers or remote control systems to switch
the product on or off.
•
Place the product in an area without any continuous sources of
ignition (for example: open flames, gas or electrical appliances in
operation).
•
When the product is installed, operated or stored in a
non-ventilated area, make sure the room is designed to prevent
the accumulation of refrigerant leaks resulting in a risk of fire or
explosion due to ignition of the refrigerant caused by electric
heaters, stoves, or other sources of ignition.
•
When defrosting and cleaning the product, do not use any
means other than those recommended by the manufacturing
company.
•
Do not puncture or heat any part of the refrigerant circuit.
Installing the product
4
Keep a minimum of 300 mm of free space around the product.
4
Only move the product in the upright position.
1. Place the product on a stable and flat surface.
2. Plug the power cable
A
5
into a power outlet.
Assembling for continuous dehumidification
(optional)
1. Remove the plug from the water hose connection
A
8
.
2. Place the water hose
A
9
into
A
8
.
3. Connect
A
9
to a water container or drainage system (not
included).
4
Ensure that
A
9
is hanging down from
A
8
, so that the water
cannot flow back into the product.
Using the control panel
Button
Function
Fan speed button
B
q
Press during the dehumidification or
ventilation mode to switch between
the high and low fan speed.
The low fan speed
B
2
or high fan
speed indicator LED
B
1
lights up.
Timer button
B
e
Press to cancel or set the duration of
dehumidification.
The timer can be set to a maximum
of 24 hours.
Press
B
r
and
B
t
to set the time.
The duration is shown in hours.
When the timer function is activated,
the time indicator LED
B
3
lights up.
- button
B
r
+ button
B
t
Press to set the desired humidity level
within a range of 30% to 80%.
Dehumidify mode button
B
y
Press to choose from four different
modes:
Automatic
Dehumidification
Dry laundry
Ventilation
Power on / standby
button
B
u
Press to switch the product on or off.
B
q
+
B
e
Press and hold
B
q
and
B
e
for 3
seconds to activate or deactivate the
child lock function.
The child lock indicator LED
B
w
lights up.
4
The product might make some noise when it is used for the first
time or after a long period when the product was not used. This
is normal and does not affect the safety of the product.
4
Keep the doors and windows closed to allow the product to work
more efficiently.
4
The room temperature might increase during use, because the
product does not have a cooling function.
Operation modes
Automatic
Automatically switches on and off to
maintain a humidity level of 55%.
Automatically switches to high fan
speed when the room humidity level
is higher than 70%.
Automatically switches to low fan
speed when the room humidity level
is between 55% and 70%.
Automatically switches to low fan
speed when the room humidity
level is lower than 55%. The
dehumidification function is disabled.
Set humidity level and fan speed are
disabled.
The automatic dehumidification
mode indicator LED
B
7
lights up.
Dehumidification
Switch on the dehumidification and
ventilator of the product.
The humidity level and fan speed can
be set manually.
The dehumidification mode indicator
LED
B
6
lights up.
Dry laundry
To help dry clothing and upholstery
in the room.
Set humidity level and fan speed are
disabled.
The dry laundry mode indicator LED
B
8
lights up.
DEHU10WT_MAN_COMP_0522_print.indd 4
DEHU10WT_MAN_COMP_0522_print.indd 4
19-5-2022 13:02:02
19-5-2022 13:02:02
