Nederman 886, Руководство пользователя, Страница: 12 / 61

Hose Reel 886
EN
7 Release the latch mechanism by pulling the hose
slightly in the direction of the arrow. Then let the
hose slowly coil up onto the reel drum.
4.3 Connection to the pipework system
See Figure 4 .
The reel must be connected to the pipework system
with an inlet hose only. Choose the right connection
position for the fixed pipework and fit the hose ac-
cording to
Figure 4 . Check that the hose is not twis-
ted after connection. A stop valve is to be fitted on
the pipe system before the hose connection, see
Fig-
ure 4 A.
5 Ratchet mechanism
See Figure 5 .
Hose Reel 886 is delivered with a ratchet mechanism
that retains the hose in the required outdrawn posi-
tion. The ratchet will disengage if the hose is drawn
out a little further and the hose then recoils to the
drum. Note that the hose should be held by hand as
long as possible during the recoiling.
NOTE!
If the hose is pulled out maximally, the ratchet
could, unfortunately, become permanently
locked. It may be released by the following pro-
cedure, see
Figure 5 A:
1 Remove the rubber plug from the drum side.
2 Carefully turn the shaft 90° clockwise to the stop
position.
NOTE!
Do not force the shaft beyond this point.
3 Pull the hose until the ratchet is released. Then let
all the hose recoil to the drum.
4 Turn the shaft 180° anti-clockwise, pass “click”
position to stop position.
5.1 Adjustment of spring tension
See Figure 6 .
WARNING! Risk of personal injury
Use protective gloves.
1 Recoil the hose until the hose stop stops against
the outlet. Pull the hose out, to a position where
the ratchet is engaged.
2 Remove the hose outlet.
3 Increasing the spring tension: Turn the drum, with
all hose wound on one revolution in the direction
of the arrow, see
Figure 6 A. Decreasing the spring
tension: Turn the drum, with all hose wound on
one revolution in the direction of the arrow, see
Figure 6 B.
4 Fit the hose outlet.
5 Check that the required length of the hose can be
pulled out without stretching the spring to its lim-
it.
6 Maintenance
CAUTION! Risk of equipment damage
Use only Nederman original spare parts and ac-
cessories.
Perform the following maintenance regularly or at
least once a year.
• Check the spring function by testing if the hose re-
coils properly.
• Check that swivel and hose couplings don’t leak.
• Change the seal if required. Clean the swivel and
couplings.
• Check the reel’s external seals. If any are cracked, all
are to be replaced.
• Check that the hose is intact. Clean the hose if dirty.
• Dismantle the hose outlet and clean the parts manu-
ally.
• Check the ratchet mechanism.
• Check the mounting of the reel on the wall or ceiling.
6.1 Changing the hose or swivel
WARNING! Risk of personal injury
Make sure to perform bullets 1-3 before start-
ing any operation in the reel:
1 Turn off the supply of media (water).
2 Pull the hose out completely.
3 Engage the safety loop, see Figure 8 .
4 Remove existing hose or swivel.
5 Fit a new hose or swivel.
6 Fit the intake hose on the swivel.
7 Fit suitable outlet gun on the distribution
8 Turn on the supply of media (water).
7 Spare Parts
CAUTION! Risk of equipment damage
Use only N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
original spare parts and ac-
cessories.
Contact your nearest authorized distributor or
N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
for advice on technical service or
if you require help with spare parts. See also
w
$
w
$
w
$
.
$
n
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
.
$
c
$
o
$
m
$
.
7.1 Ordering spare parts
When ordering spare parts always state the following:
• The part number and control number (see the
product identification plate).
12