NEC VT560 Скачать руководство пользователя страница 8

Страница: 8 / 15

8 of 15

Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX

99-00590-00 Rev A0

4. Using the supplied 7/16" nut driver, adjust the bolt inside the access hole until approximately three threads of the bolt

(or .25") protrude beyond the nut. As it may be difficult to actually see the threads, you may need to reach inside the
access hole and feel the threads behind the nut with your fingers.

NOTE

: This adjusts the angle of the small mirror so that it’s optimally aligned with the large rear mirror. This is the best

starting point for further small-mirror adjustments.

5. Move to the rear of the cabinet, and use the security key to loosen the three button head screws that secure the

projector to the projector plate.

6. Slide the projector as far forward (towards the screen) as possible and then tighten the screws you just loosened.

The top of the screen image should be approximately 3–3.5" from the upper frame. If the gap at the top of the screen is

less

than 3.5", proceed directly to step 7.

CAUTION

not

turn the small-mirror adjustment bolt more than three full clockwise turns. Turning the bolt too far

clockwise may crush the spring that is an essential part of the adjustment mechanism.

Electronics Tray

Содержание VT560
















Результаты поиска

Содержание VT560

Отзывы:

Похожие инструкции для VT560

Бренды по названию

Популярные бренды

NEC VT560, Инструкция по замене

Результаты поиска

Содержание VT560

Отзывы:

Похожие инструкции для VT560

Бренды по названию

Популярные бренды