NEC VT560 Скачать руководство пользователя страница 14

Страница: 14 / 15

14 of 15

Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX

99-00590-00 Rev A0

b. Lower the projector plate by one letter location (for example, lower the plate from I-9 to J-9) and then replace and

secure the fastening hardware.

c. Repeat if the keystone differential between the top and bottom of the image remains greater than 3/4". Proceed to

step 4.

3. If the image is wider at the top than the bottom (in excess of 3/4"), adjust the projector so that it’s slightly angled

upwards, as described in the following steps.

a. While a second person supports the projector, use the security key to loosen and then remove the two button-head

screws

in the letter locations only.

b. Raise the projector plate by one letter location (for example, raise the plate from I-9 to H-9) and then replace and

secure the fastening hardware.

c. Repeat if the keystone differential between the top and bottom of the image remains greater than 3/4".

4. Move to the front of the cabinet, and use the supplied 7/16" nut driver to turn the bolt inside the Electronics Tray access

hole counterclockwise, adjusting the angle of the small mirror to raise the top of the image to the meet the upper frame
of the cabinet.

Move the

projector plate
downwards at
the letter screw
location only

Move the

projector plate
upwards at the
letter screw
location only.

Содержание VT560
















Результаты поиска

Содержание VT560

Отзывы:

Похожие инструкции для VT560

Бренды по названию

Популярные бренды

NEC VT560, Инструкция по замене

Результаты поиска

Содержание VT560

Отзывы:

Похожие инструкции для VT560

Бренды по названию

Популярные бренды