NEC Univerge SV9100 Скачать руководство пользователя страница 48

Страница: 48 / 77

To Cancel Repeat Redial:

1. Press the

Feature

key.

2. Press the

Redial

key.

-OR-

Press the Repeat Redial key (Service Code 751:29).

Caller ID

Answer

Receive incoming ringing or a transferred outside call:

1. Review the telephone display for the calling party’s

name or number.

2. Answer the call accordingly.

Temporary Memory

An unanswered call will cause the

Call History

key

(Service Code 751:08) to flash, indicating a new call
has been placed in the temporary memory. If enabled
in programming, the telephone’s display will show:

“Check List”.

1. Press the

Call History

key (Service Code 751:08)

or press the

LIST

Softkey and CID.

Note:

The last addition to the list is displayed.

2. Press the

Arrow Down

Softkey to scroll through the

list of numbers in memory.

3. Press the

DEL

Softkey to delete the entry and scroll

to the next entry.

4. The

Call History

key will remain on as long as

entries remain in memory.

5. To place a call back to a number in the temporary

memory list, with the number to be dialed
displayed, press a Line or the

Speaker

key.

Note:

The outgoing call is placed.

CANCEL REPEAT DIAL

2-14 THU 3:15PM

List Dir VMsg



[Missed]

Ken Kobus
Tel:7205

LIST MENU

Redial CID

12345678

Line 001

Conf Rpt Save Trf

Содержание Univerge SV9100














































































Результаты поиска

Содержание Univerge SV9100

Отзывы:

Бренды по названию

Популярные бренды

NEC Univerge SV9100, Руководство пользователя

Результаты поиска

Содержание Univerge SV9100

Отзывы:

Бренды по названию

Популярные бренды