NEC POWERMATE VE - 07-1996 Скачать руководство пользователя страница 91

Страница: 91 / 152

Setting System Parameters 4-13

Boot Option Parameters

PARAMETERS

OPTIONS

DESCRIPTION

Summary Screen Enabled (default)

Disable

Displays system configuration at the
end of boot-up.

Floppy Check

Enabled (default)
Disabled

Verifies diskette type during bootup.
Disabling speeds boot time.

Last Boot Fail

3 (default)
User-selectable settings
Disabled

Sets the number of times you can
attempt to boot the system. If the
system fails to boot on the set
number of tries, the “Previous Boot
Incomplete” message appears and
the system boots with default
settings.

The default setting, 3, gives you
three tries to boot the system before
the “Previous Boot Incomplete”
message appears.

NumLock

Select “NumLock” directly from the Main Menu summary
window to display the Keyboard Features menu.

Use the legend keys to make your selections and exit to the
Main Menu. Use the following table to configure the
keyboard parameters.

Содержание POWERMATE VE - 07-1996

























































































































































Результаты поиска

Содержание POWERMATE VE - 07-1996

Отзывы:

Похожие инструкции для POWERMATE VE - 07-1996

Бренды по названию

Популярные бренды

NEC POWERMATE VE - 07-1996, Руководство пользователя

Результаты поиска

Содержание POWERMATE VE - 07-1996

Отзывы:

Похожие инструкции для POWERMATE VE - 07-1996

Бренды по названию

Популярные бренды