NEC NEC-FA150ATUA Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 47

background image

Page 4

Circuit Description

NEC-FA150ATUA

l

Input port:

-Up to 135 Mpixels/sec (Available for B grade ver.)
-24/48-bit RGB programmable, (one or two pixel-per-clock respectively)
-Seperate / composite syncs
-Glue-less interface to analog front end ICs
-TMDS receiver interface
-Interface to NTSC-digital decode ICs (YUV to RGB conversion, simplified inter less processing.)

l

Display port:

-Up to 135 Mpixels/sec (by 48bit RGB port/B grade ver.)
-24/48-bit RGB programmable. (one or two pixel-per-clock LCD panel respectively)
-Supports 18-bit and 24-bit display
-Programmable timing generator

l

PICT clock rate conversion:

-50Hz to 75Hz input refresh rates for VGA to SXGA
-50Hz to 75Hz output refresh rate (must be the same as input rate)
-No extermal frame memory required

l

Programmable picture processing:

-High quality picture scaling
-Up/down scaling from VGA, SVGA, XGA, or SXGA to XGA
-Indenpendent horizontal and vertical scaling
-Edge enhancement / smoothing (M66611)
-Color conversion with keeping white balance (M66611)
-Color space expanding to 24-bit full color for 18-bit LCD panel
-1024-extry gamma table for each R,G, B color (M66611)

6. System reset, LED control circuit (Circuit diagram MAIN PWB 4/6)

6.1 System reset
System reset is performed by detecting the rising and falling of the 3.3V source voltage at I309.
There are two kinds of resets;hardware and software. In both cases, operation is the same after the reset. (See Software
Reset for details of software resets.) This section explains on hardware resets.
When the supply voltage is in the range where operation is guaranteed, a reset is effected by holding the reset pin level
L (0.2Vcc max.) for at least 20 cycles. When the reset pin level is then returned to the H level while main clock is
stable, the reset status is cancelled and program execution resumes from the address in the reset vector table.
Figure 6.1 showns the example reset circuit. Figure 6.2 shows the reset sequence.

6.2 LED control circuit
Green / amber is lit with the control signal of the LED GREEN and LED AMBER signal pin 66, 65 from I306 (Circuit
diagram MAIN PWB 4/6).

«
...
5
6
7
8
9
...
»

Содержание NEC-FA150ATUA
















































Отзывы:

Нет отзывов

Похожие инструкции для NEC-FA150ATUA

FPT5084 - 50" Plasma TV

Бренд: Samsung Страницы: 83

460Pn - SyncMaster - 46" LCD Monitor

Бренд: Samsung Страницы: 151

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 4

Бренд: Tanaka Страницы: 21

Бренд: Allen-Bradley Страницы: 46

Бренд: Oricom Страницы: 36

Бренд: Displays2go Страницы: 23

grass valley MV-831

Бренд: Belden Страницы: 2

Бренд: HANNspree Страницы: 23

Бренд: HAOYU Страницы: 9

Бренд: B.Well Страницы: 36

Бренд: Yasun Страницы: 19

Бренд: AOC Страницы: 47

BRAILLEX ELc Series

Бренд: Papenmeier Страницы: 24

Бренд: Samar Страницы: 15

Бренд: Samsung Страницы: 47

Бренд: Samsung Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды