㻌
Confirm WWPN addresses at the computer boot (UEFI)
If the Boot Mode setting is "UEFI", follow the instructions below to confirm WWPN addresses.
㻌
1> Confirm that this product is properly connected with the Fiber Channel device. Then, turn on the
computer.
2> Set "Enabled" the Option Rom of PCI slot which installed this product, then save changes and
reboot the computer. Refer to the computer's User's Guide for how to enable the Option Rom of PCI
slot.
3> Select “UEFI Driver Configuration” submenu in the SETUP utility of the computer. Refer to the
computer's User's Guide for how to use the SETUP utility.
4> Select this product (LPe12002) from the list of devices which UEFI driver loaded. Then, check the
Node Name Value, when this menu is displayed. By changing the Node Name header “2000” to
“1000”, you will get WWPN address.
Example: Node Name “2000 0090 FA21 1128” -> WWPN address”1000 0090 FA21 1128”
ᴾ
ᴾ ᴾ ᴾ ᴾ ᵎᵎᵏᵘᴾᵪᵮᶃᵏᵐᵎᵎᵐᵋᵫᵖᵋᵬᴾᵮᵡᵧᶃᵐᵌᵓᵥᶀᵍᶑᴾᵊᴾᶖᵖᴾ
ᴾ ᴾ ᴾ ᴾ ᵪᵮᶃᵏᵐᵎᵎᵐᵋᵫᵖᵋᵬᴾᵬᶍᶂᶃᴾᵬᵿᶋᶃᴾᵘᴾᵐᵎᵎᵎᵎᵎᵗᵎᵤᵟᵐᵏᵏᵏᵐᵖᴾ
ᴾ ᴾ ᴾ ᴾ ᵱᶃᶅᵁᵘᴾᵎᵎᵎᴾᵠᶓᶑᵁᵘᴾᵒᵎᴾᵢᶃᶔᵁᵘᴾᵎᵎᴾᵤᶓᶌᶁᵁᵘᴾᵎᵎᴾ
ᴾ
ᵰᵣᵡᵭᵬᵬᵣᵡᵲᴾᵢᵣᵴᵧᵡᵣᵱᴾ
ᵱᶃᶒᴾᵠᶍᶍᶒᴾᶄᶐᶍᶋᴾᵱᵟᵬᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᴾ ᵹᵢᶇᶑᵿᶀᶊᶃᵻᴾ
㚔
ᵱᶁᵿᶌᴾᶄᶍᶐᴾᵤᶇᶀᶐᶃᴾᵢᶃᶔᶇᶁᶃᶑᴾ
㚔
ᵟᶂᶂᴾᵠᶍᶍᶒᴾᵢᶃᶔᶇᶁᶃᶑᴾ
㚔
ᵢᶃᶊᶃᶒᶃᴾᵠᶍᶍᶒᴾᵢᶃᶔᶇᶁᶃᴾ
㚔
ᵡᶆᵿᶌᶅᶃᴾᵠᶍᶍᶒᴾᵢᶃᶔᶇᶁᶃᴾᵭᶐᶂᶃᶐᴾ
㚔
ᵡᶍᶌᶄᶇᶅᶓᶐᶃᴾᵦᵠᵟᴾᵿᶌᶂᴾᵠᶍᶍᶒᴾᵮᵿᶐᵿᶋᶃᶒᶃᶐᶑᴾ
㚔
ᵱᶃᶒᴾᵣᶋᶓᶊᶃᶖᴾᵟᶂᵿᶎᶒᶃᶐᴾᶒᶍᴾᵢᶃᶄᵿᶓᶊᶒᴾᵱᶃᶒᶒᶇᶌᶅᶑᴾ
㚔
ᵢᶇᶑᶎᶊᵿᶗᴾᵟᶂᵿᶎᶒᶃᶐᴾᵧᶌᶄᶍᴾ
ᴾ
ᴾ
ᴾ
The LPe12002 of Func# “00” is Port0 and Func# “01” is Port1.
The above menu sample is just for your reference. Some of them may be
different depending on the computer or its configurations.
5> Press <Esc> key to return to the list of devices, and confirm the WWPN address of the other port of
this product by the same step from 4>.
6> If you have confirmed all WWPN address of this product, restore Option ROM settings which had
changed in step 2>. Then save changes and reboot the computer.
䣖䣫䣲䣵
Port0
