1. Verify the packed contents
Verify the packed contents with the part list given below and ensure that all the components and parts are present. Also, check that each item
is undamaged. If a component or part is missing or damaged, contact your dealer.
1
2
Part
name
Qty
1 Internal
LTO 1
2 *1
Bracket 2
Screw1
4
3
Screw2 *2
4
4
Startup Guide (this manual)
1
3
4
*1
For main unit installation
*2
For Device Expansion Unit installation
2. User’s manual and driver
User’s Manual and driver is available in website.
Refer to the user 's manual for driver installation.
http://www.nec.com/express/
3. Mounting on the Server
The procedure for installing the drive in a server is as follows.
To install in device expansion unit (N8141-69F), refer to the device expansion unit’s user’s manual.
Some servers require bracket or other latching rails to be used. For details on how to install these parts, refer to the
server's operating manual.
Please use the correct latching rails which are attached with the system, and use the screws
attached to the Internal LTO for server’s latching rails.
Use the screws attached to the server for bracket.
The attached screws are metric screws (4.0 mm length, 3.5 mm under its washer).
Using a longer screw than them may cause damage to the Internal LTO internally and
malfunction may occur.
(1) Attach the bracket or latching rail as shown in the figure A.
The presence or absence of latching rail attaching, refer to the server's operating manual.
To install in the device expansion unit (N8141-69), see figure B to attach the bracket of its accessary.
(2) Install the Internal LTO into the server.
(3) Connect the SAS cable and DC cable to the drive as shown in the figure below.
N8151-141 Internal LTO5, N8151-142 Internal LTO6
N8151-143 Internal LTO7
(4) After connecting the SAS cable, bundle the cables so that it does not interfere with the other devices or fan.
(5) Attach the cover to the server. Plug the power cable to the outlet.
(6) Turn on the server.
Figure A
Figure B
Use the screw2
attached the Internal
LTO to fix.
If use bracket attached to
the Internal LTO, use the
screw1 attached to the
Internal LTO.
4. Part name and Function
N8151-141 Internal LTO5, N8151-142 Internal LTO6
①
Cartridge insert
Slot in which the cartridge is inserted.
②
Encrypt LED (blue)
The Encrypt LED provides information about the state of the encryption with light.
③
Clean LED (amber)
The Clean LED provides information about cleaning of the drive.
④
Tape LED (amber)
The Tape LED provides information about a defect of a cartridge inserted the drive.
⑤
Drive LED (amber)
The Drive LED provides information about error of the hardware of the drive.
⑥
Ready LED (green)
The LED provides information about the state of the drive with light.
⑦
EJECT button
Press this button when ejecting a cartridge.
⑧
Ventilator
The ventilator cools and ventilates inside of the device.
N8151-143 Internal LTO7
5. Setting the Data Cartridge
(1) Ensure the drive LED goes on.
(2) Confirm that the Write Protect Switch is correctly set.
(3) Insert the data cartridge into the data cartridge slot slowly. When the cartridge is
inserted at the middle, it is automatically installed into the right position.
Do not change the position for the write protect switch during
the drive is installed into the drive. It may cause the error if the
position is changed with installation.
When the data cartridge is need to be re-installed at the eject
position, once the cartridge is removed from the drive, then,
once again, re-installation will be done
6. Ejecting the Data Cartridge
(1) Confirm that the power for the Internal LTO is on.
(2) Press the eject button. The drive rewinds the tape and partially ejects the cartridge.
The eject cycle will take a few minute.
(3) After the cartridge partially ejects, grasp the cartridge and remove it.
Regulatory
Notices
FCC Statement
Note
：
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Industry Canada Class A Emission Compliance Statement/Avis de conformité à la réglementation d‘Industrie Canada
：
CAN ICES-3(A)/NMB-3(A)
CE / Australia and New Zealand Statement
Warning : This equipment is compliant with Class A of EN55032. In a residential environment this equipment may cause radio interference.
Importer EU Contact :NEC Nederland B.V. Olympia 4, 1213 NT Hilversum, The Netherlands
BSMI Statement
警告使用者：
此為甲類資訊技術設備、於居住環境中使用時、可能會造成射頻擾動、
在此種情況下、使用者會被要求採取某些適當的對策．
KC
기 종 별
사 용 자 안 내 문
A 급기기
(업무용방송통신기자재)
이 기기는 업무용
(A
급
)
전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기바라며
,
가정외의
지역에서 사용하는 것을 목적으로 합니다
.
This product, is supplied, warranted and supported by NEC. NEC
’
s warranty and
support terms and conditions, contact points and procedures
take precedence over
those of HPE. Per EU Decision 768/2008/EC, HPE is the manufacturer of record.
