NEC N8100-1794F Скачать руководство пользователя страница 127

Страница: 127 / 128

1. Specifications

Express5800/R120d-1M User’s Guide

127

Chapter 4 Appendix

Specifications

Product name

Express5800/R120d-1M

N code

N8100-1794F

CPU

N8101-545F

N8101-546F

N8101-547F

N8101-550F

N8101-551F

N8101-552F

Intel ®Xeon® processor

E5-2609

E5-2630L

E5-2640

E5-2650L

E5-2670

E5-2690

Clock speed

2.40 GHz

2.00 GHz

2.50 GHz

1.80 GHz

2.60 GHz

2.90 GHz

Number of CPUs,

standard/maximum

1/2

3rd cache

10M

15M

20M

Number of cores (C) / Number of

threads (T) per CPU

4C/4T

6C/12T

8C/16T

Chipset

Intel® C602-J chipset

Memory

Capacity, standard/maximum

Not pre-installed /Unbuffered DIMM: 64GB (16x 4GB), Registered DIMM: 384GB (24x 16GB),

Load Reduced DIMM: 768GB (24x 32GB)

Memory module

DDR3L-1333 Unbuffered DIMM (4GB), DDR3L-1600 Registered DIMM (2/4/8/16GB),

DDR3L-1333 Load Reduced DIMM (32GB)

Maximum operating frequency

1066MHz

1333MHz

1600MHz

Error check, correction

ECC, x4 SDDC, Memory LockStep (x8 SDDC)

Memory sparing

Supported

Memory mirroring

Supported

Auxiliary

storage

Hard disk

drive

Internal (standard)

–

Internal (maximum) 2.5-inch HDD: SATA 8TB (8x 1TB), SAS 7.2TB (8x 900GB),

2.5-inch SSD: SATA 800GB (8x 100GB),

SAS 3.2TB (8x 400GB)(with optional HDD cage installed)

Hot swap

Supported

Interface / RAID level

SATA 3, 6Gb/s : RAID 0/1/5/6/10/50/60 (Option)

SAS 6Gb/s : RAID 0/1/5/6/10/50/60 (Option)

Optical disk drive

Internal or external drive (option) *1

FDD

Option: Flash FDD (1.44MB) *2

Expansion bay

None

Expansion

slots

Supported slots

1x PCI EXPRESS 3.0 (x16 lane, x16 socket) (Full hight, length 220 mm)

1x PCI EXPRESS 3.0 (x8 lane, x8 socket) (Low profile, length 220 mm)

1x PCI EXPRESS 3.0 (x8 lane, x8 socket) (Dedicated to RAID Controller)

1x PCI EXPRESS 3.0 (x8 lane, x8 socket) (Dedicated to LAN riser card)

Graphics Chip/VideoRAM

Embedded management controller chip / 32 MB

Graphic display / resolution

16,770,000 colors: 640x840, 800x600, 1,024x768, 1,280x1,024

Interface

9x USB 2.0 (2x front, 4x rear, x3 internal), 2x Analog RGB (Mini D-sub15-pin, 1x front, 1x rear),

1x Serial port (RS-232C compliant / D-sub 9-pin, Serial port A, 1x rear, optional port can be used

(up to two ports in total).

2x 1000BASE-T LAN connector (1000BASE-T/100BASE-T/10BASE-T supported, RJ45, 2x rear),

1x Management LAN connector (100BASE-T/10BASE-T supported, RJ45, 1x rear)

Power supply unit

Not pre-installed /

450W or 800W 80 Plus® Platinum compliant (bipolar grounded outlet) (hot-plug available)

maximum: 2 units)

100/200 VAC

10%, 50/60 Hz

3 Hz

Redundant power supply

Supported (option, hot-plug available)

Redundant fan

Supported (standard, hot-plug unavailable)

External dimensions (width

depth

height)

440.0mm x 720.0mm x 43.4mm (front bezel/ protrusions/ inner rails excluded)

479.7mm x 908.2mm x 43.6mm (front bezel/ protrusions/ inner rails included)

Weight (Standard/ Max.)

17 kg / 23 kg (including rails)

Power consumption

(100V at maximum

configuration)

High-load state

550 VA/540W 510VA/500W 580VA/570W 530VA/520W 620VA/610W 660VA/650W

C environment

550VA/540W 510VA/500W 580VA/570W 530VA/520W 620VA/610W 660VA/650W

Environmental requirements

Temperature/Humidity

Operating: 10 to 40

C / 20 to 80%,

Storage: –10

～

C / 20 to 80% (no condensation either when operating or when stored)

Main accessories

EXPRESSBUILDER (NEC ESMPRO Manager) (Windows),

NEC ESMPRO Agent, User’s Guide (electronic document) included),

Getting Started, one-touch rack rail

Installed OS

–

Supported OSs

Microsoft Windows Server 2003 R2, Standard Edition (SP2 or later), Microsoft Windows Server

2003 R2, Enterprise Edition (SP2 or later),

Microsoft Windows Server 2003 R2, Standard x64 Edition (SP2 or later), Microsoft Windows

Server 2003 R2, Enterprise x64 Edition (SP2 or later),

Microsoft Windows Server 2008 Standard (RTM, SP2 or later), Microsoft Windows Server 2008

Enterprise (RTM, SP2 or later),

Microsoft Windows Server 2008 Standard (x64) (RTM, SP2 or later), Microsoft Windows Server

2008 Enterprise (x64) (RTM, SP2 or later),

Microsoft Windows Server 2008 R2 Standard, Microsoft Windows Server 2008 R2 Enterprise

If you do not intend to install an internal DVD-ROM or an internal DVD SuperMULTI in all systems, prepare at least one external DVD-ROM per
system for maintenance and OS reinstallation purposes.

Prepare this if required. For the principal uses of a Flash FDD, refer to the notes on Flash FDD in the Maintenance Guide.

Содержание N8100-1794F

































































































































Результаты поиска

Содержание N8100-1794F

Отзывы:

Похожие инструкции для N8100-1794F

Бренды по названию

Популярные бренды

NEC N8100-1794F, Руководство пользователя

Результаты поиска

Содержание N8100-1794F

Отзывы:

Похожие инструкции для N8100-1794F

Бренды по названию

Популярные бренды