background image

English-25

English

TILE MATRIX

Allows one image to be expanded and displayed over multiple screens (up to 100) through a 
distribution amplifi er.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate 
without a distribution amplifi er at a lower number of screens.
This function is released when selecting IMAGE FLIP except for NONE.
Dynamic or Zoom will not work when Tile Matrix is activated.
When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting 
will be applied after completing of TILE MATRIX. 

H MONITORS

Number of monitors arranged horizontally.

1

V MONITORS

Number of monitors arranged vertically.

1

POSITION

Select which section of the tiled image to be displayed on the monitor.

1

TILE COMP

Turns the TILE COMP feature on.

NO

TILE MATRIX ENABLE

Enables Tile Matrix.

NO

FRAME COMP

Sets the tiled image timing to be displayed on the monitor. Large number makes large infl uence 
to displayed image.
NOTE: If FRAME COMP is set to AUTO or MANUAL, V SCAN REVERSE is not available.
The image may be distorted when turning the power on or changing the settings.

NONE

NONE

FRAME COMP is not available.

AUTO

Sets display timing to vertical direction of all monitors automatically.

MANUAL

Sets display timing to individual monitor.

V SCAN REVERSE*

1

Reverse scanning image direction. Normal scanning direction is top to bottom. 
NOTE: If V SCAN REVERSE is set to AUTO or MANUAL, FRAME COMP is not available.

NONE

NONE

V SCAN REVERSE is not available.

AUTO

Sets automatically calculated image scanning direction to all monitors.

MANUAL

Sets scanning direction to individual monitor.

NON REVERSE

Sets normal scanning direction and delays 1 frame display image timing.

REVERSE

Reverse scanning direction to individual monitor.

TILE MATRIX MEM

When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.

COMMON

AUTO TILE MATRIX 
SETUP

Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally 
and vertically on the primary monitor. Following settings are set automatically: MONITOR 
ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in 
TERMINAL SETTING.
NOTE: All monitors which follow in the chain with LAN should be ON. When executing this 
function while in standby mode or power save mode, “LAN POWER” should be set to ON. 
AUTO ID will be automatically executed. When you use this function, it is recommended that 
monitors are chained by DisplayPort cable.

Example of installation via LAN:

H MONITORS 

3

V MONITORS  

3

Primary monitor

DEACTIVATE

POWER ON DELAY

Adjusts the delay time between being in “standby” mode and entering “power on” mode.

DELAY TIME

“POWER ON DELAY” can be set between 0 and 50 seconds.

0 SEC.

LINK TO ID

When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number.

OFF

VIDEO OUT SETTING

Enables the signal output from DPORT. See also page 28 “DisplayPort” in TERMINAL SETTING.
NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT. 
When this function is ON, DPORT cannot be selected as the sub picture. When this function is 
ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT 
is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.

ON

POWER INDICATOR

Turns ON or OFF the LED located at the back of the monitor.
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

ON

*1: Except for X464UNS/X554UNS/X554UNV.

Содержание MultiSync X554UNV


























































Отзывы: