NDS 90T0007 Скачать руководство пользователя страница 31

Страница: 31 / 66

Setup Menu

Menu Position

Places the menu in 1 of 9 predefined screen positions. Touch the

button to select any of the 9

screen positions. The default position is in the lower left corner.

Language

The

ConductOR

currently supports English only.

DPMS Enable

Display Power Management System. This function is not supported on the

ConductOR

Auto Source Select

This function is not supported on the

ConductOR

Menu Lock

The menu may be locked via an external control program.

Operating Hours:

This function is not supported on the

ConductOR

BIOS:

Version of the

ConductOR

’s Scalar firmware.

Factory Defaults

Displays Restoring Factory Defaults message and returns all settings to their factory preset values. Touch
the

SCROLL

button (page 20) to highlight

Factory Defaults

, then touch the

button.

User Defaults

This function is not supported on the

ConductOR

Defaults Menu

Содержание 90T0007



































































Результаты поиска

Содержание 90T0007

Отзывы:

NDS 90T0007, Руководство пользователя, Страница: 31 / 66

Результаты поиска

Содержание 90T0007

Отзывы: