NDS 90T0007 Скачать руководство пользователя страница 10

Страница: 10 / 66

Connector Panel

Notes:

1. There are 8 video inputs, 4 are fixed and 4 removable. Two

S-VIDEO

, two

COMP

VGA/SOG IN

and a

DVI/RGBS/YPbPr

comprise the fixed inputs. The Fixed Inputs table, on the previous page, describes the

capabilities and limitations of the fixed inputs.

2. Currently 2 types of input modules are available:

3G-SDI

and

DVI-D

. A maximum of 4 input modules

may be installed in any combination.

3. Currently 3 types of output modules are available:

FIBER

DVI-D

and

3G-SDI

. A maximum of 4 output

modules may be installed in any combination.

AUDIO

accepts an analog input from a microphone (

MIC

). The audio output (

OUT

) is a line level analog

output. The signal presented to the

OUT

connector is intended for use with headphones. If a speaker is

required this output may be connected to an amplifier or amplified speaker.

5. When the unit is in receive mode,

YPbPr OUT

outputs the video data that is inbound to the

streamer

This data may viewed by selecting

LAN

as the input for the active display. See

Select Input Screen

page 10 and

Primary and Secondary Input Screens

on page 11. The

DVI-D OUT

outputs video data

from the selected

Stream Source

. See

IP Streaming

on page 15.

6. Audio data is retrieved from the

ETHERNET

connection, converted to analog and presented to the

OUT

connector.

7. The

ETHERNET

port has two connectors, allowing multiple

ConductORs

to be connected together and

then be connected to a PC or network via a single cable.

COM Connector

Each output module has an RJ-22

COM

connector which allows the

ConductOR

to control a

Radiance

EndoVue

display via its RS-232 port. The RJ-22’s pin out and a

ConductOR

Radiance

EndoVue

cable wiring diagram are on page 53. The required serial commands document is described in the

General Information

section on the previous page.

Unused Connectors

These connectors are not used: USB, S-VIDEO OUT, RS-232 OUT and LINE IN.

Содержание 90T0007



































































Результаты поиска

Содержание 90T0007

Отзывы:

NDS 90T0007, Руководство пользователя, Страница: 10 / 66

Результаты поиска

Содержание 90T0007

Отзывы: