manualshive.com logo in svg

Nds surgical imaging Zero Wire Duo, Руководство пользователя

Поделиться
Скачать
Nds surgical imaging Zero Wire Duo Скачать руководство пользователя страница 6

1 

ii 

Recycling: 

Follow local governing ordinances and recycling plans regarding the recycling or disposal of this 
equipment. 

Safety Compliance: 

This device meets the requirements of EN-60601-1 so as to conform to the Medical Device 
Directive 93/42/EEC and 2007/47/EC (general safety information). 

Safety Compliance: 

This device is T.U.V. approved WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL 
HAZARDS 

ONLY IN ACCORDANCE WITH 

UL 60601-1/CAN/CSA C22.2 NO. 60601-1 and 

ANSI/AAMI ES60601-1. 

FCC Identification: 

UEZTZM7201 

Radio Approval: 

This device meets the requirements of EN 302 065 V1.2.1 and conforms to Radio and 
Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. 

0673 

Warnings and Cautions 

This product complies to the above standards 

only

 when used with the supplied medical grade power 

supply.   

Power Supply: 

Ault MW172KB2400F02 or Ault MW172KB2400B02 

AC Input: 

100 to 240 Volts at 50 to 60 Hz. 

DC Output: 

24 volts at 0.75 amps 

Power Cord: 

Use a hospital grade power cord with the correct plug for your power source.  

Disconnect the power cord from the AC mains. The power cord is the only recognized disconnect device. 
The MEDICAL EQUIPMENT should be positioned so that its disconnect device is readily accessible.  
 
The device should be powered from a center tapped circuit when used  in the US at voltages over 120 
volts.  This product is intended for continuous operation.  

This symbol alerts the user that important information regarding the installation and / or 
operation of this equipment follows. Information preceded by this symbol should be read 
carefully in order to avoid damaging the equipment. 
 
This symbol warns user that un-insulated voltage within the unit may have sufficient magnitude 
to cause electrical shock. Therefore, it is dangerous to make contact with any part inside the unit. 
To reduce the risk of electric shock, 

DO NOT 

remove cover (or back). There are no user serviceable 

parts inside.

 

Refer servicing to qualified service personnel. 

 
This symbol cautions the user that important information regarding the operation and / or 
maintenance of this equipment has been included. Information preceded by this symbol should 
be read carefully to avoid damage to the equipment. 

 

This symbol denotes the manufacturer.  

 

 

This symbol denotes the manufacturer’s European Community representative. 

 

To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not use this unit's 
polarized plug with an extension cord receptacle or other outlets unless the prongs can be fully inserted. 
The product is designed to meet the medical safety requirements for a patient vicinity device.  
This equipment/system is intended for use by healthcare professionals only.  

Содержание Zero Wire Duo





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды